Kubota G2160 Скачать руководство пользователя страница 265

Страница: 265 / 395

8-S25

G2160, WSM

ELECTRICAL SYSTEM

(2) Thermo Switch

Connector Voltage

1. Disconnect the 1P connector from the thermo switch (1).
2. Turn the main switch key to the “ON” position, and measure the

voltage with a voltmeter between the connector terminal and the
chassis.

3. If a certain voltage is not indicated, the wiring harness or coolant

temperature gauge is faulty.

W1020374

Thermo Switch Continuity

1. Disconnect the 1P connector, and remove the thermo switch.
2. Using an ohmmeter, check for continuity between the switch

terminal and the chassis as shown in the figure.

3. If infinity is indicated at temperature over factory specifications,

the switch is faulty.

W1020510

(3) Fuel Pump

Connector Voltage

1. Disconnect the 2P connector from the fuel pump.
2. Turn the main switch key to the “ON” position, and measure the

voltage with a voltmeter between the connector terminals.

3. If the voltage differs from the battery voltage, the wiring harness

or main switch is faulty.

W1028106

Fuel Pump Continuity

1. Disconnect the 2P connector from the fuel pump.
2. Check the continuity between the connector terminals with an

ohmmeter.

3. If it does not conduct, the fuel pump is faulty.

W1028246

Voltage (Connector
terminal - Chassis)

Factory spec.

A certain voltage is
indicated

(1) Thermo Switch

Working temperature

Factory spec.

120 to 126

248.0 to 258.8

(A) ON
(B) OFF

(C) 116

C (240.8

F) or more

(D) 120 to 126

C (248.0 to 258.8

Connector voltage

Factory spec.

Approx. battery voltage

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 265 / 395

Результаты поиска

Содержание G2160

Отзывы: