manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 393 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 393

Q9-S8

G2160-R48S, WSM

MOWER

Backlash between Bevel Gears

1. Remove the gear case cap (2).
2. Place fuses the 21T bevel gear (3) on the pinion shaft.
3. Turn the pinion shaft.
4. Take out the fuses, and measure the thickness of fuses with an

outside micrometer.  Backlash equals thickness of fuse.

5. If the backlash is not within the factory specifications, adjust with

shims (1), (4).

6. Apply red lead lightly over several teeth at three positions equally

spaced on the bevel gear.

7. Turn the pinion shaft.
8. Check the tooth contact.  If not proper, adjust with shims (1), (4).

IMPORTANT

■

• After checking the tooth contact, check the backlash

between pinion shaft and bevel gear again.

• After the backlash has been adjusted, turn the pinion shaft

by hand to make sure it moves smoothly.

(Reference)

• Thickness of adjusting shims (1):

0.2 mm (0.0079 in.) (Part No. :36330-28420)
0.3 mm (0.0118 in.) (Part No. :36330-28410)

• Thickness of adjusting shims (4):

0.1 mm (0.0039 in.) (Part No. :70712-33570)
0.2 mm (0.0079 in.) (Part No. :76539-33410)

W1014294

Checking Proper Contact

More than 35 % red lead contact area on the gear tooth surface.

The center of tooth contact at 1/3 of the entire width from the small
end.

W1014886

Backlash between bevel 
gears

Factory spec.

0.13 to 0.25 mm
0.0052 to 0.0098 in.

Turning force

Factory spec.

Less than 14 N
Less than 1.4 kgf
Less than 10 lbs

Turning torque

Factory spec.

Less than 0.7 N·m
Less than 0.07 kgf·m
Less than 0.5 ft-lbs

(1) Shims
(2) Gear Case Cap

(3) 21T Bevel Gear
(4) Shims

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов