Kubota G2160 Скачать руководство пользователя страница 99

Страница: 99 / 395

1-S39

G2160, WSM

ENGINE

Oil Clearance between Piton Pin and Small End Bushing

1. Measure the piston pin O.D. where it contacts the bushing with

an outside micrometer.

2. Measure the small end bushing I.D. with an inside micrometer,

and calculate the oil clearance.

3. If the oil clearance exceeds the allowable limit, replace the

bushing. If it still exceeds the allowable limit, replace the piston
pin.

W11420110

Replacing Small End Bushing

(When removing)
1. Press out the used bushing using a small end bushing replacing

tool.

(When installing)
1. Clean a new small end bushing and bore, and apply engine oil to

them.

2. Insert a new bushing onto the tool and press-fit it with a press so

that the seam (1) of bushing positions as shown in the figure, until
it is flash with the connecting rod.

3. Drill a hole to the bushing with aligning the oil hole (2) of

connecting rod using 4.0 mm dia. (0.157 in. dia.) drill.

NOTE

■

• Be sure to chamfer the oil hole circumference with an oil

stone.

W11437590

Piston Ring Gap

1. Insert the piston ring into the lower part of the cylinder (the least

worn out part) with a piston ring compressor and piston.

2. Measure the ring gap with a feeler gauge.
3. If the measurement exceeds the allowable limit, replace the

piston ring.

W11466710

Oil clearance between
piston pin and small end
bushing

Factory spec.

0.014 to 0.038 mm
0.00055 to 0.00150 in.

Allowable limit

0.10 mm
0.0039 in.

Piston pin O.D.

Factory spec.

20.002 to 20.011 mm
0.78748 to 0.78783 in.

Small end bushing I.D.

Factory spec.

20.025 to 20.040 mm
0.78839 to 0.78897 in.

(1) Seam
(2) Oil Hole

(A) When Removing
(B) When Installing
(a) 0.79 rad (45

)

Piston ring gap

Top ring
Oil ring

Factory
spec.

0.15 to 0.30 mm
0.0059 to 0.0118 in.

Allowable
limit

1.25 mm
0.0492 in.

Second ring

Factory
spec.

0.30 to 0.45 mm
0.0118 to 0.0177 in.

Allowable
limit

1.25 mm
0.0492 in.

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 99 / 395

Результаты поиска

Содержание G2160

Отзывы: