manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 195 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 195

5-S23

G2160, WSM

STEERING

Checking Continuity between the Torque Sensor 3P Connector
and EPS Controller 16P Connector

1. Using a circuit tester, check continuity between the terminals.

Refer to the figure below.

2. If the resistance is out of factory specification, repair or replace

the wire harness with new one.  If the resistance is okay, replace
the power steering assembly with new one.

IMPORTANT

■

• In checking continuity, also swing the cable behind the

connector.
Be very careful to keep the circuit tester probes tight at the
terminals.

W1017512

(7) Error Codes and Defective Sections

Read the error code on the warning lamp display and take measures as shown in the table below.
For the procedures for taking measures, refer to page 5-S6.

W1018006

NOTE

■

• Resetting method (Reset after performing checking based on the error code.)

#1: Turn off the main switch and then turn it on.
#2: Perform fail-safe history erasing.

Resistance
(between same color terminal)

Factory spec.

0 

Ω

Resistance
(between different color terminal)

Factory spec.

∞

 

Ω

(1) Torque Sensor 3P Connector
(2) EPS Controller 16P Connector (view 

from the wire connected side)

(3) Notch
(4) Black/White Terminal

(5) Red Terminal
(6) White Terminal
(7) Red Terminal
(8) Black Terminal
(9) White Terminal

System name

Error 

code

Estimated defective section

Reset

Reference 

section

Power 

source

Fuse 30A

Sensor

Motor

EPS Controller

4P

16P

    Power system

02

✩

✩

✩

✩

#1

5-S6

03

✩

✩

5-S7

05

✩

✩

5-S7

06

✩

✩

5-S8

15

✩

✩

✩

5-S9

17

✩

✩

5-S10

19

✩

✩

5-S10

22

✩

✩

5-S10

    Torque sensor system

11

✩

✩

#2

5-S8

12

✩

✩

5-S9

13

✩

✩

5-S9

    EPS controller inside

23

✩

✩

✩

#1

5-S11

32

✩

✩

5-S12

34

✩

✩

5-S12

35

✩

5-S13

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов