Kubota G2160 Скачать руководство пользователя страница 105

Страница: 105 / 395

1-S45

G2160, WSM

ENGINE

Cylinder Wear

1. Measure thecylinder liner I.D. at the six positions (see figure)

with a cylinder gauge to find the maximum and minimum I.D.’s

2. Get the difference (Maximum wear) between the maximum and

the minimum I.D.’s

3. If the wear exceeds the allowable limit, bore and hone to the

oversize dimension. (Refer to “Correcting Cylinder”.)

4. Visually check the cylinder wall for scratches. If deep scratches

are found, the cylinder should be bored. (Refer to “Correcting
Cylinder”.)

W10360060

Correcting Cylinder

1. When the cylinder is worn beyond the allowable limit, bore and

hone it to the specified dimension.

2. Replace the piston and piston rings with oversize ones.

NOTE

■

• When the oversize cylinder is worn beyond the allowable

limit, replace the cylinder block with a new one.

W10367470

Cylinder liner I.D.

Factory spec.

67.000 to 67.019 mm
2.63779 to 2.63854 in.

Maximum wear

Allowable limit

+0.15 mm
0.0059 in.

(A) Top
(B) Middle
(C) Bottom (Skirt)

(a) Right-angled to Piston Pin
(b) Piston Pin Direction

Cylinder liner I.D.

Factory spec.

67.250 to 67.269 mm
2.64764 to 2.64839 in.

Maximum wear

Allowable limit

+0.15 mm
0.0059 in.

Finishing

Hone to 1.2 to 2.0 mR max.

(0.000047 to 0.0079 in.R max.)

Oversize

Part Name

Code Number

Marking

0.25 mm
0.0098 in.

Piston

1E051-21901

025 OS

Piston ring assembly

16853-21091

025 OS

(1) Cylinder I.D. (Before Correction)

(2) Oversized Cylinder I.D.

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды