manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 334 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 334

P1-S22

G2460G, WSM

ENGINE

Distributor

IMPORTANT

■

• Because adjustment of ignition timing affects the

constituents of exhaust, WG752 conforming with U.S. EPA
and CARB  SOREs (Small Off Road Engines) emission
regulations are made tamper resistant, so that operators,
users or unauthorized KUBOTA repair shops can not easily
tamper with the adjustments.

• If the ignition timing has to be adjusted, remove the tamper

resistance from the distributor mounting screw.  Reseal
securely after adjusting the ignition timing.

1. Set the plug draw-out bolt (2) to the tamper plug (3), and draw out

the tamper plug (3).

2. Remove the distributor mounting bolt (1) using hexagon wrench.
3. Remove the distributor (4).

W1047508

(1) Distributor Mounting Bolt
(2) Plug Draw-out Bolt

(3) Tamper Plug
(4) Distributor

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов