Kubota G2160 Скачать руководство пользователя страница 109

Страница: 109 / 395

1-S49

G2160, WSM

ENGINE

(B) Radiator

CAUTION

• When removing the radiator cap, wait at least ten minutes after the engine has stopped and cooled down.

Otherwise, hot water may gush out, scalding nearby people.

Radiator Water Leakage

1. Pour a specified amount of water into the radiator.
2. Set a radiator tester (1) (Code No. 07909-31551) and an adapter

(2) (BANZAI Code No.RCT-2A-30S) and raise the water
pressure to the specified pressure.

3. Check the radiator for water leaks.
4. For water leak from the pinhole, repair with the radiator cement.

When water leak is excessive, replace the radiator.

W10387530

Radiator Cap Air Leakage

1. Set a radiator tester (1) and adaptor (2) (BANZAI Code No.RCT-

2A-30S) on the radiator cap.

2. Apply the specified pressure (88 kPA, 0.9 kgf/cm

, 13 psi), and

measure the time for the pressure to fall to 59 kPa (0.6 kgf/cm

9 psi).

3. If the measurement is less than the factory specification, replace

the radiator cap.

W1054156

(C) Thermostat

Thermostat Valve Opening Temperature

1. Suspend the thermostat in the water by a string with its end

inserted between the valve and seat.

2. Heating the water gradually, read the temperature when the

valve opens and leaves the string.

3. Continue heating and read the temperature when the valve

opens approx. 6 mm (0.236 in.).

4. If the measurement is not within the factory specifications,

replace the thermostat.

W10390350

Radiator water leakage
test pressure

Factory spec.

132 kPa
1.3 kgf/cm

19 psi

(1) Radiator Tester

(2) Adaptor

Pressure falling time

Factory spec.

More than 10 seconds
for pressure fall from
88 to 59 kPa
(from 0.9 to 0.6 kgf/cm

from 13 to 9 psi)

(1) Radiator Tester

(2) Adaptor

Thermostat’s valve
opening temperature

Factory spec.

80.5 to 83.5

176.9 to 182.3

Temperature at which
thermostat completely
opens

Factory spec.

203

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 109 / 395

Результаты поиска

Содержание G2160

Отзывы: