Kubota G2160 Скачать руководство пользователя страница 103

Страница: 103 / 395

1-S43

G2160, WSM

ENGINE

Oil Clearance between Crankshaft Journal and Crankshaft
Bearing 1

1. Measure the O.D. of the crankshaft front journal with an outside

micrometer.

2. Measure the I.D. of the crankshaft bearing 1 with an inside

micrometer, and calculate the oil clearance.

3. If the oil clearance exceeds the allowable limit, replace the

crankshaft bearing 1.

4. If the same size bearing is useless because of the crankshaft

journal wear, replace it with an undersize one referring to the
table and the figure.

(Reference)

• Undersize crankshaft bearing 1

• Undersize dimensions of crankshaft journal

W10323470

Replacing Crankshaft Bearing 1

(When removing)
1. Press out the used crankshaft bearing 1 using a crankshaft

bearing 1 replacing tool.

(When installing)
1. Clean a new crankshaft bearing 1 and crankshaft journal bore,

and apply engine oil to them.

2. Using a crankshaft bearing 1 replacing tool, press in a new

bearing 1 (2) so that its seam (1) directs toward the exhaust
manifold side. (See figure)

W10342000

Oil Clearance between
crankshaft journal and
crankshaft bearing 1

Factory spec.

0.034 to 0.106 mm
0.00134 to 0.00417 in.

Allowable limit

0.20 mm
0.0079 in.

Crankshaft journal O.D.

Factory spec.

39.934 to 39.950 mm
1.57221 to 1.57284 in.

Crankshaft bearing 1 I.D.

Factory spec.

39.984 to 40.040 mm
1.57417 to 1.57638 in.

Undersize

Bearing

Code Number

Marking

0.2 mm

0.008 in.

Crankshaft bearing 1
02

15861-23911

020 US

0.4 mm

0.016 in.

Crankshaft bearing 1
04

15861-23921

040 US

Undersize
Dimension

0.2 mm
0.008 in.

0.4 mm
0.016 in.

1.8 to 2.2 mm radius
0.071 to 0.087 in.radius

5.0 mm dia.
0.20 in. dia.

5.0 mm dia.
0.20 in. dia

39.734 to 39.750 mm
1.56433 to 1.56496 in.

39.534 to 39.550 mm
1.55646 to 1.55709 in.

(0.8-S)

The crankshaft journal must be fine-finished to higher than .

Dimension (A)

Factory spec.

0.0 to 0.3 mm
0.000 to 0.012 in.

(1) Seam
(2) Crankshaft Bearing 1

(3) Cylinder Block

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 103 / 395

Результаты поиска

Содержание G2160

Отзывы: