Kubota G2160 Скачать руководство пользователя страница 335 | Manualshive

Страница: 335 / 395

Kubota G2160 Скачать руководство пользователя страница 335

P1-S23

G2460G, WSM

ENGINE

(When reassembling)

NOTE

■

• When placing the distributor over the distributor drive shaft,

make sure that the distributor drive groove is horizontal
when No. 1 cylinder is at its T.D.C..
At this time, the mating mark should be at the bottom.

1. Tighten the distributor mounting bolt (7).
2. Using a timing light, check that the ignition timing (stamps on the

flywheel) (6) is aligned with the mark (5) on the rear end plate (4).

3. If the timing is wrong, loosen the distributor mounting screw (7)

and turn the distributor (8) so that the ignition timing (stamps on
the flywheel) is aligned with the mark on the rear end plate.

4. Drive the plug (9) into the hexagonal hole (11) of bolt with hand.
5. Insert the plug completely with fitting jig (10).

W1047715

Ignition timing

Factory spec.

0.315 rad (18

°

)

before T.D.C.

(1) Mating Mark on the Distributor
(2) Mating mark on the Distributor Drive
(3) Flywheel
(4) Rear End Plate
(5) Mark
(6) Ignition Timing Mark on Flywheel
(7) Distributor Mounting Screw
(8) Distributor

(9) Tamper Plug

(10) Fitting Jig

(11) Hexagonal Hole in Distributor

Mounting Screw

(A) To Retard
(B) To Advance

KiSC issued 11, 2006 A

«
...
333
334
335
336
337
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов