Kubota G2160 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 395

Kubota G2160 Скачать руководство пользователя страница 87

1-S27

G2160, WSM

ENGINE

Piston

1. Turn the flywheel and bring the No.1 piston to the top dead

center.

2. Pull out the piston upward by lightly tapping it from the bottom of

the crankcase with the grip of a hammer.

(When reassembling)

• Before inserting the piston into the cylinder, apply enough engine

oil to the cylinder.

• When inserting the piston into the cylinder, face the mark on the

connecting rod to the injection pump.

IMPORTANT

■

• Do not change the combination of cylinder and piston. Make

sure of the position of each piston by marking. For example,
mark “1” on the No.1 piston.

• When inserting the piston into the cylinder, place the gap of

the compression ring 1 on the opposite side of the
combustion chamber and stagger the gaps of the
compression ring 2 and oil ring making a right angle from
the gap of the compression ring 1.

• Carefully insert the pistons using a piston ring compressor.

Otherwise, their chrome-plated section may be scratched,
causing trouble inside the cylinder.

W10277450

(A) Top Ring Gap
(B) Second Ring Gap
(C) Oil Ring Gap
(D) Piston Pin Hole

(a) 0.79 rad (45

°

)

(b) 0.79 rad (45

°

)

(c) 0.79 rad (45

°

)

KiSC issued 11, 2006 A

«
...
85
86
87
88
89
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов