Kubota G2160 Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 395

Kubota G2160 Скачать руководство пользователя страница 135

2-S13

G2160, WSM

TRANSMISSION AND REAR AXLE

(2) Separating Hydrostatic Transmission

Neutral Arm, Speed Control Arm and Hydraulic Pipes

1. Remove the neutral spring (10).
2. Remove the neutral arm assembly mounting screws (11).
3. Remove the neutral arm assembly (9).
4. Remove the speed control arm set screw (4).
5. Remove the speed control arm (5).
6. Remove the stopper plate (8).
7. Remove the suction pipe (1) with the oil strainer.
8. Remove the adaptor plates (3).
9. Remove the drain pipe retaining bolt (2).
10.Remove the drain pipe (7) with the hydraulic hoses.
11.Remove the drain plug (6).
(When reassembling)

• Take care not to damage the O-ring.

IMPORTANT

■

• Once removed, the speed change arm set screw is not

reusable.

W1026369

Separating Hydrostatic Transmission

1. Remove the adaptor bolts (1) with the gaskets.
2. Remove the hydrostatic transmission mounting screws (2), (3).
3. Separate the hydrostatic transmission from the front cover.
(When reassembling)

• First tighten the adapter bolts into the control valve assembly.

Then tighten up control valve assembly stay mounting screw.

W1026829

Tightening torque

Drain pipe retaining bolt
(9/16-18 UNF)

27.4 N·m
2.8 kgf·m
20.3 ft-lbs

Speed control arm set
screw

17.6 to 20.6 N·m
1.8 to 2.1 kgf·m
13.0 to 15.2 ft-lbs

Neutral arm assembly
mounting screw

17.6 to 20.6 N·m
1.8 to 2.1 kgf·m
13.0 to 15.2 ft-lbs

Drain plug

36.3 N·m
3.7 kgf·m
26.8 ft-lbs

(1) Suction Pipe
(2) Drain Pipe Retaing Bolt
(3) Adaptor Plates
(4) Speed Control Arm Set Screw
(5) Speed Control Arm
(6) Drain Plug

(7) Drain Pipe
(8) Stopper Plates
(9) Neutral Arm Assembly

(10) Neutral Spring

(11) Neutral Arm Assembly Mounting

Screw

Tightening torque

Adapter bolt (PS3/8)

80.4 N·m
8.2 kgf·m
59.3 ft-lbs

(1) Adaptor Bolts
(2) Hydrostatic Transmission Mounting

Screw

(3) Hydrostatic Transmission Mounting

Screws

KiSC issued 11, 2006 A

«
...
133
134
135
136
137
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов