Kubota G2160 Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 395

Kubota G2160 Скачать руководство пользователя страница 136

2-S14

G2160, WSM

TRANSMISSION AND REAR AXLE

(3) Separating Transmission

Separating Control Valve Assembly

1. Remove the control valve assembly stay mounting screw (4).
2. Separating the control valve assembly (1) from the transmission.
3. Remove the collar (3) and O-ring (2) on the front cover.
(When reassembling)

• Take care not to damage the O-ring.
• Temporarily tighten the control valve assembly stay mounting

screw.

• First tighten the adapter bolts into the control valve assembly.

Then tighten up the control valve assembly stay mounting screw.

W1027118

Separating Transmission

1. Separating the left rear axle case (3) from the transmission case.
2. Take out the differential assembly (1), noting the number of left

and right shims (2).

3. Separate the rear axle support (5) and the right rear axle case (4)

from the transmission.

4. Take out the yoke shaft (7) and spline boss (6).
(When reassembling)

• Take care not to damage the O-ring.
• Install the adjusting shims to their original position.

W1027308

(4) Disassembling Transmission

(A) Hydrostatic Transmission

NOTE

■

• Work in a clean area.
• Replace any damaged parts that could cause internal leakage.
• Do not use grit paper, files or grinders on finished surface.
• Use only clean, recommended fluid on the finished surface in reassembling.

Charge Relief Valve

1. Remove the relief plug (3).
2. Remove the spring (2) and charge relief cone (1).

NOTE

■

• If shims are placed at the bottom of the relief plug bore, keep

them.

• Take care not to damage the O-ring.

W1027643

(1) Control Valve Assembly
(2) O-ring

(3) Collar
(4) Control Valve Assembly Stay

Mounting Screw

(1) Differential Assembly
(2) Shims
(3) Left Rear Axle Case
(4) Right Rear Axle Case

(5) Rear Axle Support
(6) Spline Boss
(7) Yoke Shaft

(1) Charge Relief Cone
(2) Spring

(3) Relief Plug

KiSC issued 11, 2006 A

«
...
134
135
136
137
138
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов