Kubota G2160 Скачать руководство пользователя страница 152

Страница: 152 / 395

3-S3

G2160, WSM

BRAKE

Parking Lock Pedal

1. Remove the parking lock pedal mounting nut (2).
2. Remove the parking lock pedal (1) from the brake lock.
(When reassembling)

IMPORTANT

■

• Using the oval hole, make such adjustment that the parking

lock pedal be kept out of contact with the panel over the
entire stroke.

• Step on the brake pedal and parking lock pedal at once, and

make sure that the speed change pedal gets locked.

• If the speed change pedal fails to get locked, set this pedal

to the neutral position and readjust the brake lock (3) so that
the lock pin (5) comes into the notch (4).

W1011595

Steering Wheel

1. Remove the grip of the throttle lever (1).
2. Remove the steering pad and remove the steering wheel

mounting nut.

3. Remove the steering wheel using the steering wheel puller

(Code, No. 07916-51090) and steering wheel puller adaptor (See
page G-40.)

IMPORTANT

■

• When removing steering wheel, use steering wheel puller.

Do not use the hammer to prevent electric power steering
from damaging.

• Remove the steering wheel after setting it to the straight-

ahead position.

(When reassembling)

W1011912

(1) Parking Lock Padal
(2) Parking Lock Padal Mounting Nut
(3) Brake Lock

(4) Notch
(5) Lock Pin

Tightening torque

Steering wheel mounting
nut

19.6 to 24.5 N·m
2.0 to 2.5 kgf·m
14.5 to 18.1 ft-lbs

(1) Throttle Lever

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды