manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 131 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 131

2-S9

G2160, WSM

TRANSMISSION AND REAR AXLE

(C) Separating Fender

Seat

1. Disconnect the 2P connector (3) from the seat switch and fuse

(4).

2. Remove the seat support mounting lock nut (1).
3. Remove the screws (5).
4. Remove the seat with seat support. 
5. Remove the seat bracket (2).
(When reassembling)

• Turn the seat support mounting lock nuts all the way until it seats

lightly.   
Then, turn seat support mounting lock nuts counterclockwise by
a half turn.

• Apply oil to the seat support.
• Face smooth side the plane washers (6) to the seat support.

W1014173

Cutting Height Adjusting Dial

1. Lift the mower to the highest position.
2. Remove the cam mounting nut (1).
3. Remove the cutting height adjusting dial, plain washer and cam

(2).

(When reassembling)

• Apply grease to the outside of cam.

W1014754

(1) Seat Support Mounting Lock Nuts
(2) Seat Bracket
(3) 2P Connector
(4) Fuse

(5) Screws
(6) Seat Support
(7) Plane Washers
(8) Fender

Tightening torque

Cam mounting nut

39.2 to 45.1 N·m
4.0 to 4.6 kgf·m
28.9 to 33.3 ft-lbs

(1) Cam Mounting Nut

(2) Cam

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов