Kubota G2160 Скачать руководство пользователя страница 62

Страница: 62 / 395

1-S2

G2160, WSM

ENGINE

W1010717

Symptom

Probable Cause

Solution

Reference
Page

Engine Revolution Is
Not Smooth

• Fuel filter clogged or dirty
• Air cleaner clogged

• Fuel leak due to loose injection pipe retaining

nut

• Injection pump malfunctioning

• Incorrect nozzle injection pressure

• Injection nozzle stuck or clogged

• Governor malfunctioning

Replace fuel filter.
Clean or replace air
cleaner element.
Tighten retaining nut.

Repair or replace
injection pump.
Adjust nozzle
injection pressure.
Repair or replace
injection nozzle.
Repair governor.

G-27
G-28

1-S20

1-S23

1-S53

1-S23
1-S25

Either White or Blue
Exhaust Gas Is
Observed

• Excessive engine oil

• Piston ring and cylinder worn or stock

• Incorrect injection timing

• Deficient compression

Reduce to specified
engine oil level.
Repair piston ring
and bore oversize
piston.
Adjust injection
timing.
Adjust top clearance

–

1-S28
1-S30
1-S45
1-S51

1-S18

Either Black or Dark
Gray Exhaust Gas Is
Observed

• Overload
• Low grade fuel used
• Fuel filter clogged
• Air cleaner clogged

• Deficient nozzle injection

Lessen load.
Use specified fuel.
Replace fuel filter.
Clean or replace air
cleaner element.
Repair or replace
nozzle

–
–

G-27

G21
G28

1-S53

Deficient Output

• Incorrect injection timing

• Engine's moving parts seem to be seized.

• Uneven fuel injection

• Deficient nozzle injection

• Compression leak from cylinder

Adjust injection
timing.
Repair or replace
engine’s moving
parts.
Repair or replace
injection pump.
Repair or replace
nozzle.
Replace head
gasket, tighten
cylinder head screws,
glow plugs and
nozzle holders.

1-S51

–

1-S53

1-S21
1-S22

Excessive Lubricant
Oil Consumption

• Piston ring's gap facing the same direction

• Oil ring worn or stuck
• Piston ring groove worn
• Valve stem and valve guide worn

• Oil leaking due to defective seals or packing

Shift ring gap
direction.
Replace oil ring.
Replace piston.
Replace valve stem
and valve guide.
Replace defective
seals or packing.

1-S27
1-S28
1-S28
1-S28
1-S33

–

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 62 / 395

Результаты поиска

Содержание G2160

Отзывы: