manualshive.com logo in svg

Basler BE1-CDS220, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-CDS220 доступна для бесплатного скачивания на manualshive.com. Этот ручной датчик обеспечивает надежное и эффективное использование устройства. Загрузите свой экземпляр сейчас, чтобы получить всю необходимую информацию о продукте.

Поделиться
Скачать
background image

6-40 

Reporting and Alarm Functions 

BE1-CDS220 

Sequence of Events information can also be obtained through BESTCOMS. Select Reports from the 
toolbar and select Oscillography Download from the drop-down menu. Select the event number and 
select View Fault Sequence of Events for details. See Figure 6-20. Select Exit when finished. 

ALARMS FUNCTION 

The alarms function monitors internal relay systems, external relay interfaces, and power system 
equipment. Alarm points are segregated into Relay Trouble Alarms and Programmable Alarms. Alarm 
point status is stored in nonvolatile memory and is retained when relay operating power is lost. 

The ability to program the reporting and display of alarms along with the automatic display priority feature 
of the HMI gives the relay the functionality of local and remote alarm annunciation. See Section 10, 
Human-Machine Interface, for more information on the automatic display priority logic. 

Relay Trouble Alarms  

All internal circuitry and software that affects how the relay functions is monitored by the continuous self-
test diagnostics function of the relay trouble alarms. A detailed list of relay trouble alarms is provided in 
Table 6-20. If any one of these points asserts, the failsafe alarm output relay de-energizes and closes the 
OUTA contact, the HMI Relay Trouble LED lights, all output relays are disabled, logic variable ALMREL is 
set, and the relay is taken offline. The relay trouble alarms function is not programmable. 

If your application requires a normally closed contact that opens to indicate a relay trouble condition, use 
BESTlogic to program the output logic. One of the output relays with normally open contacts (OUT1 
through OUT6) can be programmed to be held closed. For example, to open OUT5 for indication of relay 
trouble, set the VO5 logic expression at /0 (SL-VO5=/0). A not zero setting is equal to logic 1. When the 
relay is fully functional, the OUT5 output contact is closed. Since all output relays are disabled when a 
relay trouble alarm exists, OUT5 opens when relay trouble occurs. 

 

Table 6-20. Relay Trouble Alarms 

I.D. # 

Name 

Description 

1 

RAM FAILURE 

Static RAM read/write error. 

2 

ROM FAILURE 

EPROM program memory checksum error. 

3 

UP FAILURE 

Microprocessor exception or self-test error. 

4 

EEPROM FATAL ERROR 

EEPROM read/write error. 

5 

ANALOG FAILURE 

Analog to digital converter error. 

6 

CALIBRATION ERR 

Relay not calibrated or calibration checksum error. 

7 

PWR SUPPLY ERR 

Power supply out of tolerance. 

8 

WATCHDOG FAILURE 

Microprocessor watchdog circuit timed out. 

9 

SET DEFLTS LOADED 

Relay using setting defaults. 

10 

CAL DFLTS LOADED 

Relay using calibration defaults. 

11 

DSP FAILURE 

Digital signal processor error. 

 

Relay trouble alarms, except for CALIBRATION ERR, EEPROM FATAL ERR, SET DFLTS LOADED, and 
CALDFLTS LOADED indicate that the relay is not functional and causes the self-test diagnostics to force 
a microprocessor reset to try to correct the problem. 

CALIBRATION ERR, EEPROM FATAL ERROR, or DFLTS LOADED errors indicate that the relay is 
functional but needs re-calibration or the settings reprogrammed. 

Any relay trouble alarm will disable the protection functions, light the Relay Trouble LED, and place the 
output contacts in their normal, de-energized state. If a relay trouble (RA-REL) alarm is cleared by 
pressing the HMI Reset key while viewing Screen 1.2 or using the RA=0 or RA-REL=0 commands, then 
the relay will attempt to return back online by issuing a software reset. The relay resets by going through 
a full startup and initialization cycle. If no problems are detected, the relay returns online and enables 
protection. 

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

Zander Aachen SR3E Operating Instructions preview
SR3E
Бренд: Zander Aachen Страницы: 4
hager EU 300 User Instructions preview
EU 300
Бренд: hager Страницы: 2
Tense MDK-03 Quick Start Manual preview
MDK-03
Бренд: Tense Страницы: 2
ZIEHL MS220C Operating Instructions Manual preview
MS220C
Бренд: ZIEHL Страницы: 8
F&F OM-630 Quick Start Manual preview
OM-630
Бренд: F&F Страницы: 2
F&F PCS-516UNI Manual preview
PCS-516UNI
Бренд: F&F Страницы: 2
F&F BIS-416 Quick Start Manual preview
BIS-416
Бренд: F&F Страницы: 2
F&F BIS-410-LED Quick Start Manual preview
BIS-410-LED
Бренд: F&F Страницы: 4
F&F BIS-411BM-LED Quick Start Manual preview
BIS-411BM-LED
Бренд: F&F Страницы: 7
ASO ISK 71?24 Operating Manual preview
ISK 71?24
Бренд: ASO Страницы: 52
LEGRAND Wattstopper LMCP-GE24 Installation Instructions preview
Wattstopper LMCP-GE24
Бренд: LEGRAND Страницы: 4
Pilz P2HZ 5 Operating Instructions Manual preview
P2HZ 5
Бренд: Pilz Страницы: 6
ZIEHL UFR1001E Quick Manual preview
UFR1001E
Бренд: ZIEHL Страницы: 8
Viessmann 5552 Operation Manual preview
5552
Бренд: Viessmann Страницы: 4
ELMON 34-32 Operating Manual preview
34-32
Бренд: ELMON Страницы: 36
Zamel exta PCM-09 User Manual preview
exta PCM-09
Бренд: Zamel Страницы: 2
Zander Aachen SR3D User Information preview
SR3D
Бренд: Zander Aachen Страницы: 4
Plejd LED-75 Installation Manual preview
LED-75
Бренд: Plejd Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды