manualshive.com logo in svg

Basler BE1-CDS220, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-CDS220 доступна для бесплатного скачивания на manualshive.com. Этот ручной датчик обеспечивает надежное и эффективное использование устройства. Загрузите свой экземпляр сейчас, чтобы получить всю необходимую информацию о продукте.

Поделиться
Скачать
background image

13-20 

Testing And Maintenance 

BE1-CDS220 

Output Terminals 

Commands 

OUT4 (N.O.) 

C9 and C10 

CS-OUT4=P,CO-OUT4=P 

OUT5 (N.O.) 

C11 and C12 

CS-OUT5=P,CO-OUT5=P 

OUT6 (NC/NO) 

C13, C14, and C15 

CS-OUT6=P,CO-OUT6=P 

 

Virtual 43 Switches 

Purpose:  To verify the operation, labels, and logic settings of the virtual 43 switches. 

Reference Commands:  SN-43, SL-43, RG-43STAT, RG-STAT, CS/CO-43 

NOTE 

If virtual 43 switches are not used, skip the eight associated steps and go to the next test. 

Step 1. 

Transmit the SN-43 command to verify the virtual selector switch 43 name, TRUE label, and 
FALSE label. This information is reported using the format SN-x43=name,TRUE label,FALSE 
label. 

Step 2. 

Repeat Step 1 for virtual selector switches 143 through 743. Use the number of a switch in the 
SN-43 command to retrieve name and label information for that switch. 

Step 3. 

Use the SL-x43 command to obtain the logic setting of virtual switches 43 through 743. Logic 
settings for virtual switches can also be obtained by using the SL command. Verify that the 
desired virtual selector switch setting matches the reported setting. 

Step 4. 

Transmit the RG-43STAT command to obtain the position of the eight virtual selector switches. 
Alternately, the virtual selector switch positions can be obtained through the RG-STAT 
command or optional HMI screens 2.1.1 through 2.1.8, \CTRL\43\43 through \CTRL\43\743. 

Step 5 

Obtain write access to the relay by using the ACCESS= command. For each virtual selector 
switch enabled in your logic scheme, change the switch position by entering CS-x43 = 1 
(TRUE), 0 (FALSE), or P (Pulse) followed by CO-x43=1,0, or P. The syntax of the CS-x43 and 
CO-x43 commands must match or the CO-x43 command won’t be executed. 

Step 6. 

Verify each switch position change by using the CO-x43 command or through optional HMI 
screens \CTRL\43\43 through \CTRL\43\743. 

Step 7. 

Leave each virtual 43 switch in the desired position for placing the protection and control 
system in service. 

Step 8. 

Verify the 43 switch activity by viewing the sequence of events reports with the RS-### 
command. 

Virtual 101 Switch 

Purpose:  To verify the operation, label, and logic setting for the 101 switch. 

Reference Commands:  SB-LOGIC, SL-101, RG-101STAT, RG-STAT, CS/CO-101 

Step 1. 

Verify the breaker label and breaker-closed logic expression with the SB-LOGIC command. 

Step 2. 

Use the SL-101 command to read the logic mode of the 101 switch. The switch is either 
enabled (1) or disabled (0). 

Step 3. 

Verify the virtual control switch status by using the RG-101STAT, RG-STAT, or CO-101 
commands or optional HMI screens 2.2, \CTRL\BKR.   

Step 4. 

Transmit the command ACCESS= to obtain write access to the relay. Change the switch 
position by entering CS-101=T (Trip) or C (Close) followed by CO-101=T (Trip) or C (Close). 
The syntax of the CS-101 and CO-101 commands must match or the CO-101 command won’t 
be executed. 

Step 5. 

Verify the switch position change as you did in Step 3. 

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

frako RM 2106/12 Operating Instructions Manual preview
RM 2106/12
Бренд: frako Страницы: 32
Furman PS-REL Instruction Sheet preview
PS-REL
Бренд: Furman Страницы: 1
OEZ SR50 Series Instructions For Use preview
SR50 Series
Бренд: OEZ Страницы: 4
Schweitzer Engineering Laboratories SEL-167D Instruction Manual preview
SEL-167D
Бренд: Schweitzer Engineering Laboratories Страницы: 123
NX NXP2-RL-SP Installation Instructions preview
NXP2-RL-SP
Бренд: NX Страницы: 3
Pilz PNOZ s3 Operating Manual preview
PNOZ s3
Бренд: Pilz Страницы: 27
Salus RM-16A Manual preview
RM-16A
Бренд: Salus Страницы: 4
ZIEHL VG1200 Quick Manual preview
VG1200
Бренд: ZIEHL Страницы: 4
Eaton EMR5-AWN500-1 Operating And Installation Instructions preview
EMR5-AWN500-1
Бренд: Eaton Страницы: 12
Eaton ESR5-NO-31-230VAC Manual preview
ESR5-NO-31-230VAC
Бренд: Eaton Страницы: 20
Moeller ESR4-NO-21 Operating Instruction preview
ESR4-NO-21
Бренд: Moeller Страницы: 6
ABB SPAM 150 C User Manual And Technical Description preview
SPAM 150 C
Бренд: ABB Страницы: 20
Eaton XTOB038CC1 Instruction Leaflet preview
XTOB038CC1
Бренд: Eaton Страницы: 3
Siemens SIRIUS 3RP2005 Original Operating Instructions preview
SIRIUS 3RP2005
Бренд: Siemens Страницы: 4
Vitals Rs 100k Manual For Technical Use preview
Rs 100k
Бренд: Vitals Страницы: 27
TopflyTech TSR1-B User Manual preview
TSR1-B
Бренд: TopflyTech Страницы: 8
PSP SAK-60 Programming Manual preview
SAK-60
Бренд: PSP Страницы: 8
Lightwave LW821 Instruction Manual preview
LW821
Бренд: Lightwave Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды