Basler BE1-CDS220 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 476

background image

BE1-CDS220 General

Information

1-21

Input Burden:

Burden per contact for sensing depends on the power
supply model and the input voltage. Table 1-1 provides
appropriate burden specifications.

Table 1-1. Control Input Burden

Burden

Power Supply

Jumper Installed

Jumper Removed

Option L (24 Vdc)

15k

Ω

N/A

Option Y (48/125 Vac/Vdc)

35k

Ω

90k

Ω

Option Z (125/250 Vac/Vdc)

90k

Ω

185k

Ω

Communication Ports

Interface:

Front RS-232 (COM 0):

300 to 19,200 baud, 8N1 full duplex

Rear RS-232 (COM 1):

300 to 19,200 baud, 8N1 full duplex

Rear RS-485 (COM 2):

300 to 19,200 baud, 8N1 half duplex

Display

Type:

Graphic LCD (liquid crystal display) with LED (light
emitting diode) back-light

Operating Temperature:

-40

°

C to 70

°

C (-40

°

F to 158

°

F) The display contrast may

be impaired at temperatures below -20

°

C (-4

°

F).

Isolation

2,000 Vac at 50/60 Hz in accordance with IEEE C37.90
and IEC 255-5. (Excludes communication ports.)

Surge Withstand Capability

Oscillatory:

Qualified to IEEE C37.90.1-1989, Standard Surge
Withstand Capability (SWC) Tests for Protective Relays
and Relay Systems

Fast

Transient:

Qualified to IEEE C37.90.1-1989, Standard Surge
Withstand Capability (SWC) Tests for Protective Relays
and Relay Systems

Radio Frequency Interference (RFI)

Type tested using a five-watt, hand-held transceiver in
the ranges of 144 and 440 MHz with the antenna placed
six inches from the relay. Qualified to C37.90.2-1995,
Standard For Withstand Capability Of Relay Systems To
Radiated Electromagnetic Interference From
Transceivers.

Electrostatic Discharge (ESD)

8 kV contact discharges and 15 kV air discharges
applied in accordance with IEC 60255-22

UL Recognition

U.L. recognized per Standard 508, U.L. File Number
E97033. Note: Output contacts are not U.L. recognized
for voltages greater than 250 V.

«
...
31
32
33
34
35
...
»

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

Бренд: Sonder Страницы: 2

Бренд: Malmbergs Страницы: 2

Бренд: Eaton Страницы: 22

Бренд: Eaton Страницы: 16

Бренд: MICROENER Страницы: 29

Бренд: LOVATO ELECTRIC Страницы: 2

Бренд: BENDIX Страницы: 4

Бренд: Projecta Страницы: 2

Бренд: Woodward Страницы: 70

Бренд: TopflyTech Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды