Basler BE1-CDS220 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 476

background image

iv

Introduction BE1-CDS220

Application

Program

Firmware

Version/Date Change

1.14.05/06-03

Corrected ND timer problem.

Enhanced in-house diagnostics.

1.14.04/10-02

Corrected triggering problem of 2

nd

oscillography record.

Allowed the differential alarm to be disabled through SA-DIFF serial command.

Improved SER most recent events reporting.

Improved 62 timer function.

Corrected help text for SG-TARG command.

Allowed Trip Led to turn off when current is removed and SG-TARG=0.

Updated 87ND time delay settings.

Correctly improper display of Q demand on LCD.

Moved the degree symbol to the proper location on the LCD for the GND
current.

Improved 50TQ and 51Q time delay functions.

1.14.03/06-01

Fixed the SG-DI command (Setting Group-Demand Interval) so that it now
recognizes a demand interval of three or more digits as being “out of range”.

Added improvements to DNP 3.0, Level 2 protocol.

Added new “Password Security” parameters to Modbus protocol.

Modified display of Phase Angle information (HMI and reports) so that an
asterisk (

∗

) appears in the angle position if the measured current is below 1%

of rated current (0.05 A for a 5 A relay, 0.01 A for a 1 A relay).

1.14.02/05-01

Corrected firmware problems with Modbus and DNP protocols.

1.14.01/09-00

Added reporting of the protocol option to the COM2 setting screen on the LCD
HMI.

Improved the arrangement of information on the current metering screens on
the HMI.

Added improvements to DNP 3.0 protocol to make it Level 2 compliant.

1.14.00/03-00

Corrected problem that caused the programmable variable names to be limited
to 10 characters instead of 16 characters. This problem occurred with version
1.13.01.

Added Mode 6, Latching Timer to 62 timer functions.

Added DNP 3.0 Protocol.

Added a feature for the demand recording function to allow the user to select
block average or sliding block average calculation method in addition to the
existing thermal calculation method.

«
...
4
5
6
7
8
...
»

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

Бренд: F&F Страницы: 7

Бренд: Zander Aachen Страницы: 4

Бренд: raditeq Страницы: 5

Бренд: Keithley Страницы: 58

Бренд: Eaton Страницы: 12

Бренд: F&F Страницы: 4

PR102 MINI-PLC 40 I/O

Бренд: Akytec Страницы: 2

Бренд: Muller Страницы: 2

Бренд: c3controls Страницы: 16

ESR5-NO-41-24VAC-DC

Бренд: Eaton Страницы: 30

Бренд: ALIND Страницы: 54

Бренд: Allen-Bradley Страницы: 2

Бренд: Thytronic Страницы: 146

Бренд: System Sensor Страницы: 2

Бренд: Ampcontrol Страницы: 71

Eagle Quantum Premier EQ3720RM

Бренд: Det-Tronics Страницы: 4

D-Mon Class 3000

Бренд: E-Mon Страницы: 4

Бренд: Sel Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды