manualshive.com logo in svg

Basler BE1-CDS220, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-CDS220 доступна для бесплатного скачивания на manualshive.com. Этот ручной датчик обеспечивает надежное и эффективное использование устройства. Загрузите свой экземпляр сейчас, чтобы получить всю необходимую информацию о продукте.

Поделиться
Скачать
background image

BE1-CDS220 Application 

8-37 

protection element from the transformer BE1-CDS220 (not shown in Figure 8-12) does not get blocked 
when the feeder relays are picked up. Therefore, the 250T protection element must be set with a time 
delay long enough to allow the feeder breaker to interrupt the fault. 

Virtual control switch elements enabled for use in this scheme are 101, 43, and 743. The 101 control 
switch trips the low-side breaker through output 4 and closes the low-side breaker through output 5. 
Control switch 43 is used to turn the 87 function on or off and 743 us used to enable Test Mode. 

Test Mode 

When virtual control switch 743 is enabled, breaker failure initiate through output 6 is defeated. 

Setting Group 

For normal operation, setting group 0 is active for the BUS-W-BU  scheme. IN7 to the BE1-CDS220 
identifies when a feeder relay (851) is out of service. At the same time, IN5 of the transformer BE1-
CDS220 scheme gets the same signal. Both relays then switch to setting group 1. Setting group selection 
mode 2, binary coded selection, is used to recognize the group setting state. When input D0 to the setting 
group selection element is a one, it is interpreted as a binary 1 causing the logic to switch to group 1. 

When the bus BE1-CDS220 is in setting group 1, it is operating in feeder backup mode. This expression is 
programmed to virtual output 14 which drives alarm bit #22 in the programmable alarm mask. It can be 
masked to drive an alarm LED and alarm display to indicate when the relay is in feeder backup mode and 
to trip a feeder breaker instead of the bus breaker. 

Alarms 

Three logic variables drive the front panel LEDs: Relay Trouble (ALMREL), Major Alarm (ALMMAJ), and 
Minor Alarm (ALMMIN). A fourth logic variable, Logic Alarm (ALMLGC), has no associated front panel 
LED. When the relay self-test detects a problem in the relay (ALMREL) as programmed for the BUS-W-
BU scheme, the Relay Trouble LED lights, output A operates, and all outputs are disabled. When a Major 
Alarm is detected (ALMMAJ), the associated LED lights, but in this scheme, no output relay is 
programmed to operate. When a Minor Alarm (ALMMIN) is detected, the associated LED lights, but in this 
scheme, no output relay is programmed to operate. 

 

 

 

CAUTION 

Test Mode Enable does not defeat the trip outputs of the relay. External trip test 
blades must be opened or the BUS-W-BU logic scheme must be modified to suit 
the user’s test mode requirements. One option is to trip the breakers through an 
86 device only. Typically, 86 devices are installed with test blades in the breaker 
trip circuit so that the protection scheme can be safely operational checked while 
the primary equipment is in service. Another option is to inhibit all trip outputs 
when test mode is enabled; however, external devices such as auxiliary relays 
and 86 devices would no longer be included in the operational test. 

NOTE 

Tables 8-22 through 8-25 provide detailed logic definitions for the inputs, outputs, 
protection, and control elements. Only those inputs, logic blocks, virtual switches, 
and outputs in use for the BUS-W-BU preprogrammed logic are described in the 
following Tables. 

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

resideo Protectorelay Installation Instructions Manual preview
Protectorelay
Бренд: resideo Страницы: 8
CTI FB800E Instruction Manual preview
FB800E
Бренд: CTI Страницы: 30
LS DMP Series Instruction Manual preview
DMP Series
Бренд: LS Страницы: 5
Zamel EXTA PCP-06 Quick Start Manual preview
EXTA PCP-06
Бренд: Zamel Страницы: 2
Siemens 7PG17-XR151 Manual preview
7PG17-XR151
Бренд: Siemens Страницы: 7
ZIEHL UFR1001E Short Operating Manual preview
UFR1001E
Бренд: ZIEHL Страницы: 8
ADLINK Technology ACLD-9185 Manual preview
ACLD-9185
Бренд: ADLINK Technology Страницы: 15
CARLO GAVAZZI RSGT Manual preview
RSGT
Бренд: CARLO GAVAZZI Страницы: 45
Rockwell Automation Allen-Bradley Guardmaster Minotaur MSR131RTP Installation Instructions preview
Allen-Bradley Guardmaster Minotaur MSR131RTP
Бренд: Rockwell Automation Страницы: 4
Rockwell Automation Allen-Bradley 193-T1D P Series Installation Instruction preview
Allen-Bradley 193-T1D P Series
Бренд: Rockwell Automation Страницы: 2
Rockwell Automation Allen-Bradley 193-T1APM Installation Instruction preview
Allen-Bradley 193-T1APM
Бренд: Rockwell Automation Страницы: 2
Rockwell Automation Allen-Bradley 193-T1C Series Installation Instruction preview
Allen-Bradley 193-T1C Series
Бренд: Rockwell Automation Страницы: 2
Rockwell Automation 592-SMP-1 Installation preview
592-SMP-1
Бренд: Rockwell Automation Страницы: 4
Rockwell Automation Allen-Bradley Guardmaster 440C-CR30 Application Technique preview
Allen-Bradley Guardmaster 440C-CR30
Бренд: Rockwell Automation Страницы: 32
Rockwell Automation Allen-Bradley 440R-GL2S2T User Manual preview
Allen-Bradley 440R-GL2S2T
Бренд: Rockwell Automation Страницы: 42
Rockwell Automation 440R-D22R2 User Manual preview
440R-D22R2
Бренд: Rockwell Automation Страницы: 90
Rockwell Automation Allen-Bradley E300 User Manual preview
Allen-Bradley E300
Бренд: Rockwell Automation Страницы: 546
Pickering PXI 40-160 Series User Manual preview
PXI 40-160 Series
Бренд: Pickering Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды