Basler BE1-CDS220 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 476

background image

BE1-CDS220 Introduction

iii

PRODUCT REVISION HISTORY

The following information provides a historical summary of the changes made to the software, embedded
software (firmware), and hardware of this device. The corresponding revisions made to this instruction
manual are also summarized. This revision history is separated into four categories: BESTCOMS
Software, Application Program Firmware Version, Hardware Version, and Manual Revision. All revisions
are listed (with the month and year) in reverse chronological order with the most recent on top.

BESTCOMS

Software

Version/Date Change

2.01.00/07-05

Improved ability to use special characters in comments.

Enhanced program to work with RS232 converters.

Corrected printout problem with long comments.

Added “Settings Compare” feature.

2.00.01/10-02

Initial 32-bit release.

Improved the 87ND function block diagram.

Corrected tap calculation reporting errors.

Improved programming of Reset Target Logic.

Corrected the SG-COM2 command to be sent out correctly.

1.01.01/12-99

Added ability to create, upload, and download settings files.

Added ability to read fault report directory and fault summary reports.

Improved communications.

1.01.00/05-99

Initial 16-bit release.

Application

Program

Firmware

Version/Date Change

1.15.00/01-06

Minor software enhancements.

1.14.10/11-05

Removed write capability from some Modbus



registers.

1.14.09/07-05

Improved LCD display.

1.14.08/09-03

Added diagnostics for in-house testing.

1.14.07/08-03

Corrected the harmonic sharing inhibit problem.

Enhanced breaker operations counter.

Corrected cal defaults loaded problem when upgrading firmware.

«
...
3
4
5
6
7
...
»

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

Бренд: Pilz Страницы: 20

Allen-Bradley 700-SA

Бренд: Rockwell Automation Страницы: 69

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 32

Relion RER615 DNP3

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 36

System pro M RHI

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 52

Бренд: ABB Страницы: 22

Бренд: ABB Страницы: 68

Бренд: ABB Страницы: 7

Бренд: ABB Страницы: 72

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 3

Бренд: ABB Страницы: 100

Бренд: ABB Страницы: 60

Бренд: ABB Страницы: 38

Бренд: ABB Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды