manualshive.com logo in svg

Basler BE1-CDS220, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-CDS220 доступна для бесплатного скачивания на manualshive.com. Этот ручной датчик обеспечивает надежное и эффективное использование устройства. Загрузите свой экземпляр сейчас, чтобы получить всю необходимую информацию о продукте.

Поделиться
Скачать
background image

10-12 Human-Machine 

Interface  BE1-CDS220 

4.  Once all of the settings on the screen have been entered, press the Edit pushbutton a second 

time and the settings will be validated. If the settings are in range, the screen will flash 
CHANGES SAVED, and the Edit LED will go out. If you want to abort the edit session without 
changing any settings, press the Reset  pushbutton before you press the Edit pushbutton the 
second time. The screen will flash CHANGES LOST and the Edit LED will go out. 

Performing Control Operations 

Control operations can be executed from the LCD HMI from menu branch 2, CONTROL. These functions 
allow you to control the state of virtual switches, override logic and control the active setting group, and 
override the logic and control the state of output contacts. All of these functions work similarly to the 
process of entering settings in that you press the Edit pushbutton, use the UP and DOWN scroll 
pushbuttons to select the desired state and press the Edit pushbutton for the action to be executed. 

Figure 10-11 shows virtual switch 243 as an example of a virtual 
switch screen. See Section 4, Protection and Control, for more 
details on the x43 and 101 functions. Table 10-4 describes each 
of the callouts shown on Figure 10-11. The user programmable 
label for this switch has been set to DIFF_CUTOFF. The TRUE 
(closed) state label has been set to NORMAL and the FALSE 
(open) state label has been set to 87_OFF. The logical mode for 
this application would be set to Mode 2 (On/Off switch). 

 

 

 

Table 10-4. Virtual Control Switches Controls and Indicators 

Locator Description 

A 

User selectable label (meaningful name) for specific virtual switches. Switch 243 
identification label set to DIFF_CUTOFF. 

B 

User selectable label for the closed (1) state for Virtual Switch 243. Switch 243 closed 
state label set to NORMAL. 

C 

User selectable label for the open (0) state for Virtual Switch 243. Switch 243 open state 
label set to 87_OFF. 

D 

Icon to show the current switch position (status). In Figure 10-11, the current status is the 
closed state, which is labeled NORMAL. 

E 

Current switch status. This indicator should correspond to the current user labeled switch 
status. The switch is closed (1) and the user label for closed is NORMAL. 

 

To operate the switch, you would use the following procedure: 

1.  Using the manual scrolling pushbuttons, scroll to Screen 2.1.x, \CTRL\43\. Alternatively, if the 

screen has been placed in the automatic scroll list, simply wait for it to appear and press the 
RIGHT or LEFT scroll pushbutton to freeze the display.  

2. Press 

the 

Edit pushbutton to gain access. If password security has been initiated for control 

functions, you will be prompted to enter the appropriate password. See the following paragraphs, 
Entering Passwords, for details on entering passwords from the HMI. Once access has been 
gained to the control function, the Edit LED will be lighted and a cursor will appear in the action 
field. 

3. Press 

the 

UP or DOWN scrolling key to select the desired action. The selections available are 

dependent upon the logic mode setting for that switch. If it is set to Mode 1, the action choices are 
pulse or one of the two positions as defined by the user programmable state labels. If the mode is 
set to Mode 2 (ON/OFF Switch), the choices for action are limited to one of the two positions. If 
the mode is set to Mode 3 (OFF/Momentary ON Switch), the choice for action is limited to pulse.  

4. Press 

the 

Edit pushbutton a second time and the switch will change to the selected position, the 

screen will flash CHANGES SAVED and the Edit LED will go out. If you want to abort the edit 
session without changing any controls, press the Reset pushbutton before you press the Edit 
pushbutton the second time. The screen will flash CHANGES LOST and the Edit LED will go out. 

\CTRL\43\243

       DIFF_CUTOFF

 ACTION

         

 NORMAL

  NORMAL

                 

87_OFF

<143           >343

2.1.3

D2840-18.vsd

 02-09-99

A

B

C

E

D

Figure 10-11. Virtual Control Switch 243 

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

LOVATO ELECTRIC PMA30 Quick Start Manual preview
PMA30
Бренд: LOVATO ELECTRIC Страницы: 6
Ortus Relay-R Operation Manual preview
Relay-R
Бренд: Ortus Страницы: 8
ABB System pro M RHI Manual preview
System pro M RHI
Бренд: ABB Страницы: 50
ABB SPAU 130 C User Manual And Technical Description preview
SPAU 130 C
Бренд: ABB Страницы: 52
ABB SRW Instruction Leaflet preview
SRW
Бренд: ABB Страницы: 22
ABB SPAJ 140 C User Manual And Technical Description preview
SPAJ 140 C
Бренд: ABB Страницы: 68
ABB Tmax T1 Manual preview
Tmax T1
Бренд: ABB Страницы: 7
ABB REU 513 User Manual preview
REU 513
Бренд: ABB Страницы: 72
ABB T16 Installation Instructions preview
T16
Бренд: ABB Страницы: 2
ABB TRB Series Instruction Leaflet preview
TRB Series
Бренд: ABB Страницы: 3
ABB Relion REX610 Operation Manual preview
Relion REX610
Бренд: ABB Страницы: 100
ABB SPAJ 131 C User Manual And Technical Description preview
SPAJ 131 C
Бренд: ABB Страницы: 60
ABB TF65 Operating Instructions Manual preview
TF65
Бренд: ABB Страницы: 38
ABB SPAU 331 C User Manual And Technical Description preview
SPAU 331 C
Бренд: ABB Страницы: 20
ABB SPAU 140 C User Manual And Technical Description preview
SPAU 140 C
Бренд: ABB Страницы: 72
ABB TD-5 Instruction Leaflet preview
TD-5
Бренд: ABB Страницы: 16
ABB SPAJ 160 C User Manual And Technical Description preview
SPAJ 160 C
Бренд: ABB Страницы: 64
ABB SDG-1T Instruction Leaflet preview
SDG-1T
Бренд: ABB Страницы: 49

Бренды по названию

Популярные бренды

Загрузить еще бренды