manualshive.com logo in svg

Basler BE1-CDS220, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-CDS220 доступна для бесплатного скачивания на manualshive.com. Этот ручной датчик обеспечивает надежное и эффективное использование устройства. Загрузите свой экземпляр сейчас, чтобы получить всю необходимую информацию о продукте.

Поделиться
Скачать
background image

13-28 

Testing And Maintenance 

BE1-CDS220 

UPDATING FIRMWARE AND SOFTWARE 

Future enhancements to relay functionality may make a firmware update desirable. Enhancements to 
relay firmware typically coincide with enhancements to BESTCOMS software for that relay. When a relay 
is updated with the latest version of firmware, the latest version of BESTCOMS software should also be 
obtained. 

Updating Relay Firmware 

If a firmware upgrade is desired, you may request a CD-ROM containing the latest firmware or download 
the firmware from the Basler Electric website. Direct your web browser to 
http://www.basler.com/BE1_Firm and complete the on line form to request a CD-ROM containing the 
latest firmware or a password for downloading firmware from the Basler Electric web site. 

Once the appropriate firmware is obtained, it can be uploaded to a relay using the BESTload software 
utility provided on the CD-ROM originally supplied with the relay. 

Updating BESTCOMS Software 

Firmware enhancements often include the addition of relay settings or the modification of existing settings. 
BESTCOMS software is revised to accommodate the new or changed settings. When firmware is 
updated, the latest version of BESTCOMS should also be obtained. If a CD-ROM was obtained from 
Basler Electric, then that CD-ROM will contain firmware and the corresponding version of BESTCOMS 
software. BESTCOMS can also be downloaded from the Basler Electric web site (http://www.basler.com). 
An on line form can be completed to obtain a password for downloading BESTCOMS from the Basler 
Electric web site. 

FUNCTIONAL TESTING 

NOTE 

Functional testing is NOT required for this unit. It is only necessary if the user wants to 
perform a comprehensive assessment to determine suitability for an application.   

Functional testing provides a comprehensive assessment of this relay to determine suitability for your 
application. Functional testing goes beyond the more basic tests found in acceptance testing, but does not 
go into the detail for each function as in Commissioning Testing. 

Test each of the following functions to verify that this relay measures accurately, is within specified 
tolerances, and operates correctly as designed. In addition, these tests are suitable for assisting in 
systematic  trouble-shooting in the event of a questionable operation. Revisiting a functional test of a 
specific function of the relay can help verify whether the relay is indeed operating within the 
manufacturer’s specified tolerance. For further assistance, contact Basler Electric, Customer Services 
Department.

 

Phase Differential (87) 

Minimum Pickup  

Purpose:  To verify the minimum pickup of the 87 elements.   

Reference Commands: SL-87,  S<g>-87, S<g>-TAP87, SG-CT 

Step 1. 

Connect one current source to terminals B1 and B2 (A-phase, input 1). See Figures 13-1 and 
13-2. An ohm-meter or continuity tester may be used to monitor output contact status. 

 

 

 

 

 

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

I-Gard SIGMA 3 Manual preview
SIGMA 3
Бренд: I-Gard Страницы: 35
Basler BE1-50/51B-229 Instruction Manual preview
BE1-50/51B-229
Бренд: Basler Страницы: 57
SymCom MOTORSAVER 460 Installation Instructions preview
MOTORSAVER 460
Бренд: SymCom Страницы: 4
nLight 876599 Installation Instructions Manual preview
876599
Бренд: nLight Страницы: 9
NIVELCO NITIME JEL-111 User Manual preview
NITIME JEL-111
Бренд: NIVELCO Страницы: 2
MSD Ignition 8961 Installation Instructions preview
8961
Бренд: MSD Ignition Страницы: 4
IFM efector 110 G1502S Original Operating Instruction preview
efector 110 G1502S
Бренд: IFM Страницы: 52
ABB HT595115 Operation Manual preview
HT595115
Бренд: ABB Страницы: 124
Pavotek DEMA DigiLine 400 Series Quick Start Manual preview
DEMA DigiLine 400 Series
Бренд: Pavotek Страницы: 11
OEZ 43239 Instructions For Use Manual preview
43239
Бренд: OEZ Страницы: 9
F&F SWITCH & ENERGY Wi-R1S1-P Manual preview
SWITCH & ENERGY Wi-R1S1-P
Бренд: F&F Страницы: 15
resideo R8845U Manual preview
R8845U
Бренд: resideo Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды