manualshive.com logo in svg

Basler BE1-CDS220, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-CDS220 доступна для бесплатного скачивания на manualshive.com. Этот ручной датчик обеспечивает надежное и эффективное использование устройства. Загрузите свой экземпляр сейчас, чтобы получить всю необходимую информацию о продукте.

Поделиться
Скачать
background image

13-2 

Testing And Maintenance 

BE1-CDS220 

faithfully, that relay logic is appropriate, and, that protective elements and equipment (main or auxiliary) 
operate correctly are goals that can be achieved during this type of testing. 

Basler Electric recommends that all captured fault records and sequence of event records be analyzed 
and kept on file as in-service periodic test results for this particular device. This is an indication that all 
protective elements and associated equipment are operating satisfactorily. 

It is not the intent of this manual to elaborate on every conceivable test possible since this would encroach 
on individual preferences, techniques, and philosophies. It is the intent to pursue relevant testing methods 
to verify this relay meets published design specifications and applicability. 

Functional Testing 

Functional (or application) testing  is significantly more comprehensive in nature and is intended to test 
suitability for a particular application. Functional testing also provides a means to familiarize yourself with 
the logic and operation of this device. Test setups are generally more involved and often times include 
ancillary equipment beyond voltage or current source type equipment. While economics may at times 
prohibit full functional testing, it is recommended that some application testing be performed when 
published specifications lack appropriate detail to satisfy application testing requirements. 

Basler Electric performs a thorough and comprehensive functional test of all relays before shipping. This 
ensures that this device is within specified tolerances, measures accurately, and operates correctly as 
designed. 

Performance Testing 

Performance testing can be accomplished through the capture and playback of system fault records. In 
actual applications, this type of test realizes further confirmation of faithful relay responses during system 
disturbances. For specific power system disturbances, relays can be subjected to a recreation of captured 
events with the aide of equipment capable of replicating COMTRADE record files. In these instances, 
there is significant merit in testing relays in this manner to assess relay performance. Correct response of 
relay action in a performance test is supplemental verification of the conclusions drawn from functional (or 
application) tests. 

This type of testing verifies not only whether or not the device operated correctly for a particular system 
disturbance, but also offers additional confirmation of your protection philosophy in this application. It is 
beyond the scope of this manual to develop performance tests for this device. For assistance in 
developing these types of tests, please consult Basler Electric and your test equipment manufacturer. 

TESTING AND TROUBLESHOOTING AIDS 

Under test or in-service, the BE1-CDS220 provides several ways to check operations, targets, or events. 
A continuous self-test monitors the system health and status. The most basic reporting function is targets. 
Targets may be viewed through ASCII command interface or through the optional front panel HMI. Fault 
Summary Reports, Sequence of Events Recorder (SER) Reports, and Oscillographic Records yield more 
detail. 

Each time a system disturbance occurs in or around this relay’s zone of protection, it is a test of the relay 
performance during the fault. If a questionable operation (or lack of) results in the need for 
troubleshooting, you have several ways in which to troubleshoot the relay, the installation, and the overall 
application. 

Relay Self-Test 

All internal circuitry and software that affect the relay core functionality are monitored by the continuous 
self-test diagnostics. For specific relay trouble alarms, the self-test diagnostics force the microprocessor to 
reset and try to correct the problem. If unsuccessful, OUTA operates, the Relay Trouble LED on the front 
panel turns ON, all of the output relays are disabled, internal logic point ALMREL is set, and the relay is 
taken off line. For more information on self-test diagnostics and relay trouble alarms, see Section 6, 
Reporting and Alarm Functions, Alarms Function. 

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

Eaton Power Xpert C445 Safety Manual preview
Power Xpert C445
Бренд: Eaton Страницы: 34
Schleicher SNO 2012 Quick Start Manual preview
SNO 2012
Бренд: Schleicher Страницы: 6
Eaton Cutler-Hammer D64RP18 Instruction Manual preview
Cutler-Hammer D64RP18
Бренд: Eaton Страницы: 17
Datalogic CS ME-03VU24-Y14 Quick Start Manual preview
CS ME-03VU24-Y14
Бренд: Datalogic Страницы: 4
Boltek ERL-10 Installation & Operator’S Manual preview
ERL-10
Бренд: Boltek Страницы: 36
ASO ELMON rail 32-242 Operating Manual preview
ELMON rail 32-242
Бренд: ASO Страницы: 32
ABB SSR32 Product Manual preview
SSR32
Бренд: ABB Страницы: 40
Siemens SIRIUS 3UG4581-1AW30 Operating Instructions preview
SIRIUS 3UG4581-1AW30
Бренд: Siemens Страницы: 4
Siemens LZS PT Series Operating Instructions Manual preview
LZS PT Series
Бренд: Siemens Страницы: 6
Siemens SIRIUS 3RR224 Series Operating Instructions Manual preview
SIRIUS 3RR224 Series
Бренд: Siemens Страницы: 14
Siemens 3UA50 Instructions preview
3UA50
Бренд: Siemens Страницы: 4
Siemens 3TS30 Operating Instructions preview
3TS30
Бренд: Siemens Страницы: 5
Siemens 3RS1800 Operating Instructions preview
3RS1800
Бренд: Siemens Страницы: 2
Siemens 3RB2483-4AA1 Original Operating Instructions preview
3RB2483-4AA1
Бренд: Siemens Страницы: 12
Siemens 3TK2856 Original Operating Instructions preview
3TK2856
Бренд: Siemens Страницы: 20
Siemens Reyrolle 7SR45 Manual preview
Reyrolle 7SR45
Бренд: Siemens Страницы: 54
CARLO GAVAZZI DTA71CM24 Technical Data, Installation And Operation preview
DTA71CM24
Бренд: CARLO GAVAZZI Страницы: 2
Woodward highprotec MRI4 User Manual preview
highprotec MRI4
Бренд: Woodward Страницы: 727

Бренды по названию

Популярные бренды

Загрузить еще бренды