manualshive.com logo in svg

Basler BE1-CDS220, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-CDS220 доступна для бесплатного скачивания на manualshive.com. Этот ручной датчик обеспечивает надежное и эффективное использование устройства. Загрузите свой экземпляр сейчас, чтобы получить всю необходимую информацию о продукте.

Поделиться
Скачать
background image

BE1-CDS220 BESTCOMS 

Software 

14-1 

SECTION 14 

•

 BESTCOMS SOFTWARE 

DESCRIPTION 

BESTCOMS is a Windows

 

based program that runs on an IBM compatible computer and provides a user 

friendly, graphical user interface (GUI) for use with Basler Electric communicating products. BESTCOMS 
is an acronym that stands for Basler  Electric  Software  Tool for Communications,  Operations, 
Maintenance, and Settings. 

BESTCOMS provides the user with a point and click means for setting and monitoring the in-service relay 
or relays under test. The point and click method provides an efficient, fast setup for configuring one or 
several relays. This software is provided free with every BE1-CDS220 Current Differential System. 

INTRODUCTION 

A primary advantage of the 32-bit BESTCOMS is that an actual unit (i.e., operating transmission 
protection system) is not required to perform any or all settings and adjustments for any preprogrammed 
scheme. Nor is it needed to create a custom scheme complete with settings and adjustments. Also, 
BESTCOMS is identical within all of the Basler Electric Numerical Systems except for differences inherit 
in the individual systems. This means that once you become familiar with a BESTCOMS for one system, 
you are also familiar with BESTCOMS for all of the systems. 

Using the BESTCOMS GUI, you may prepare setting files off-line (without being connected to the relay) 
and then upload the settings to the relay at your convenience. These settings include protection and 
control, operating and logic, breaker monitoring, metering, and fault recording. Engineering personnel can 
develop, test, and replicate the settings before exporting them to a file and transmitting the file to 
technical personnel in the field. In the field, the technician simply imports the file into the BESTCOMS 
database and uploads the file to the relay where it is stored in nonvolatile memory. (See the paragraphs 
on  File Management later in this manual for more information on saving, uploading, and downloading 
files.) 

The BESTCOMS GUI also has the same preprogrammed logic schemes that are stored in the relay. This 
gives the engineer the option (off-line) of developing his/her setting file using a preprogrammed logic 
scheme, customizing a preprogrammed logic scheme, or building a unique scheme from scratch. Files 
may be exported from the GUI to a text editor where they can be reviewed or modified. The modified text 
file may then be uploaded to the relay. After it is uploaded to the relay, it can be brought into the GUI but 
it cannot be brought directly into the GUI from the text file. The GUI logic builder uses basic AND/OR gate 
logic combined with point and click variables to build the logic expressions. This reduces the design time 
and increases dependability. 

The BESTCOMS GUI also allows for downloading industry-standard COMTRADE files for analysis of 
stored oscillography data. Detailed analysis of the oscillography files may be accomplished using Basler 
Electric's BESTwave software. For more information on Basler Electric's Windows

 based BESTwave 

software, contact your local sales representative or Basler Electric, Technical Support Services 
Department in Highland, Illinois. 

This section provides an introduction to all of the screens in the BE1-IPS100 Intertie Protection System 
with their field layouts and typical entries. Common program activities such as applying settings, 
modifying logic, and setting up password security are discussed. These discussions are application 
oriented. We explore how the activity or task can be performed using an appropriate BE1-IPS100 
BESTCOMS screen.   

BESTCOMS screens are similar to most Windows

 based GUI screens. You may immediately notice 

common features such as the pull-down menu, toolbar, icons, and help prompts when the mouse pointer 
is paused over an icon. Some of these features are shown in Figure 14-1. If the Navigation Bar has a right 
and left arrow at the extreme right hand side of the screen, clicking on these arrows will shift the 
Navigation Bar to allow access to all of the icons on the bar. Like most computer programs, there is often 
more than one way to perform an activity or task. These various methods are discussed in the following 
paragraphs in conjunction with the appropriate BESTCOMS screen. 

 

 

 

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

M-system R7M-RR8 Instruction Manual preview
R7M-RR8
Бренд: M-system Страницы: 4
Identiv PRIMIS FR-50-40-E Installation Manual preview
PRIMIS FR-50-40-E
Бренд: Identiv Страницы: 2
MSD Ignition 8961 Installation Instructions preview
8961
Бренд: MSD Ignition Страницы: 4
System Sensor R-10E Installation And Maintenance Instructions preview
R-10E
Бренд: System Sensor Страницы: 2
Schweitzer Engineering Laboratories SEL-487V Manual preview
SEL-487V
Бренд: Schweitzer Engineering Laboratories Страницы: 32
krom schroeder IFW 15T-N Operating Instructions preview
IFW 15T-N
Бренд: krom schroeder Страницы: 4
Schweitzer Engineering Laboratories SEL-167D Instruction Manual preview
SEL-167D
Бренд: Schweitzer Engineering Laboratories Страницы: 123
M-system R7C-DC8E Instruction Manual preview
R7C-DC8E
Бренд: M-system Страницы: 5
Sola HD RELAYCARD-SDU Instruction Manual preview
RELAYCARD-SDU
Бренд: Sola HD Страницы: 6
Watts Switching Relay 303P Series Installation Manual preview
Switching Relay 303P Series
Бренд: Watts Страницы: 12
Eaton ES4A-221-DMX-SIM Installation Instructions preview
ES4A-221-DMX-SIM
Бренд: Eaton Страницы: 2
GE Multilin HID Instruction Manual preview
Multilin HID
Бренд: GE Страницы: 23
GE CEY52B Instructions Manual preview
CEY52B
Бренд: GE Страницы: 36
GE IAV53K Instructions preview
IAV53K
Бренд: GE Страницы: 4
Eaton Cutler-Hammer CEP7 Series Instruction Leaflet preview
Cutler-Hammer CEP7 Series
Бренд: Eaton Страницы: 4
Eaton EMR-5000 Installation, Operation And Maintenance Manual preview
EMR-5000
Бренд: Eaton Страницы: 1060
GE MLJ1000 Manual preview
MLJ1000
Бренд: GE Страницы: 42
Zamel exta PNM-10 User Manual preview
exta PNM-10
Бренд: Zamel Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды