manualshive.com logo in svg

Basler BE1-CDS220, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-CDS220 доступна для бесплатного скачивания на manualshive.com. Этот ручной датчик обеспечивает надежное и эффективное использование устройства. Загрузите свой экземпляр сейчас, чтобы получить всю необходимую информацию о продукте.

Поделиться
Скачать
background image

BE1-CDS220 General 

Information 

1-1 

SECTION 1 

•

 GENERAL INFORMATION 

DESCRIPTION 

The BE1-CDS220 Current Differential System is an economical, microprocessor based, multifunction 
system that provides two-input, three-phase percentage differential with harmonic restraint, three-phase, 
ground, and negative sequence overcurrent protection with control, breaker failure, breaker monitoring, 
transformer monitoring, and metering functions in an integrated system with communications. The 
BE1-CDS Current Differential System is intended for use in any low impedance current differential 
protection application including transformer, generator, motor, and bus protection. Four setting groups are 
provided for adaptive relaying with automatic selection logic for cold load pickup and/or dynamic setting 
group changes. 

BE1-CDS relays have eight programmable contact sensing inputs, six programmable outputs, and one 
alarm output. Outputs can be assigned various functions by logical programming to perform protection, 
control, or indicator operations. For example, protection functions could cause a protective trip operation. 
Control functions could cause a manual trip, manual close or automatic reclose operation. Indicators 
could be relay fail, setting group one enable, setting group two enable, and others. 

Protection scheme designers may select from a number of pre-programmed logic schemes that perform 
the most common protection and control requirements or create a custom scheme using BESTlogic.   

A  Quick Start, Section 2, provides BE1-CDS Current Differential System users with a simplified How to 
Get Started procedure. 

FEATURES 

The BE1-CDS220 relay includes many features for the protection, monitoring, and control of power 
system equipment such as transformers, breakers, buses, generators, and motors. These features 
include protection and control functions, metering functions, and reporting and alarm functions. A highly 
flexible programmable logic system called BESTlogic allows the user to apply the available functions with 
complete flexibility and customize the system to meet the requirements of the protected power system. 
Programmable I/O, extensive communications features, and an optional advanced HMI (Human Machine 
Interface) provide easy access to the features provided. BE1-CDS220 relay users with personal 
computers (PC) have another easy access means to communicate, program, control, and monitor 
relay/system performance. That means is BESTCOMS for BE1-CDS220. BESTCOMS is a Windows

 

based software application that enhances communication between the PC user and the BE1-CDS220 
relay. This software is provided free with every BE1-CDS220 relay. Another software application tool is 
BESTWAVE. BESTWAVE is a utility program to view standard COMTRADE (Common Format for 
Transient Data Exchange) files and Basler UMOS (Utilities Management Operating System) files captured 
by the Basler Electric multifunction relays. This software is available free of charge through the web site at 
http://www.basler.com or Customer Service at the Highland, Illinois manufacturing facility. 

The following information summarizes the features included in this multifunction device. The organization 
of this information outlines organization of the rest of the manual. Each feature, along with how to set it up 
and how to use the outputs is described in complete detail in the later sections of this manual. 

Input and Output Functions 

Power System Measurement Functions 

•

  Two sets of three-phase currents are digitally sampled and digitally filtered. The fundamental, 

second, and fifth harmonics are extracted using a Discrete Fourier Transform (DFT) algorithm for 
use by all of the current based functions. 

•

 

Neutral (residual) and negative sequence current magnitudes are derived from each set of three-
phase currents. 

•

 

Each set of three-phase currents can be phase-shift and tap compensated for use in transformer 
differential applications.  

•

 

The digital sampling rate tracks the measured frequency to provide high accuracy at frequencies 
other than nominal frequency to make this relay ideally suited for applications such as generator, 
motor, and generator step-up transformer differential protection. 

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

Eaton easyE4 series Application Note preview
easyE4 series
Бренд: Eaton Страницы: 29
Eaton easyE4 series Manual preview
easyE4 series
Бренд: Eaton Страницы: 621
Pilz 750136 Operating Instructions Manual preview
750136
Бренд: Pilz Страницы: 16
Zander Aachen SR3E Operating Instructions preview
SR3E
Бренд: Zander Aachen Страницы: 4
CAMDEN CX-33PS Installation Instructions Manual preview
CX-33PS
Бренд: CAMDEN Страницы: 26
HANYOUNG NUX HSR-SLD15LR Series Instruction Manual preview
HSR-SLD15LR Series
Бренд: HANYOUNG NUX Страницы: 2
HANYOUNG NUX HSR-2E Instruction Manual preview
HSR-2E
Бренд: HANYOUNG NUX Страницы: 2
Littelfuse PGR-8800 User Manual preview
PGR-8800
Бренд: Littelfuse Страницы: 82
Ice IMM 8001 User Manual preview
IMM 8001
Бренд: Ice Страницы: 97
Esco TC-11 Manual preview
TC-11
Бренд: Esco Страницы: 8
ZIEHL TR600 Operating Manual preview
TR600
Бренд: ZIEHL Страницы: 16
Moeller ETR4-70A Installation Instructions preview
ETR4-70A
Бренд: Moeller Страницы: 2
Moeller DILM-C Series Installation Instructions preview
DILM-C Series
Бренд: Moeller Страницы: 2
Moeller PFR-5 Installation Instructions preview
PFR-5
Бренд: Moeller Страницы: 5
Moeller EASY 412-AC Series Training Manual preview
EASY 412-AC Series
Бренд: Moeller Страницы: 55
KAEL VARko-106-TFT Manual preview
VARko-106-TFT
Бренд: KAEL Страницы: 16
CAMDEN CX-12 PLUS Installation Instructions Manual preview
CX-12 PLUS
Бренд: CAMDEN Страницы: 15
Siemens AG8 101-103 Manual preview
AG8 101-103
Бренд: Siemens Страницы: 100

Бренды по названию

Популярные бренды

Загрузить еще бренды