manualshive.com logo in svg

Basler BE1-CDS220, Инструкция по эксплуатации

Инструкция по эксплуатации Basler BE1-CDS220 доступна для бесплатного скачивания на manualshive.com. Этот ручной датчик обеспечивает надежное и эффективное использование устройства. Загрузите свой экземпляр сейчас, чтобы получить всю необходимую информацию о продукте.

Поделиться
Скачать
background image

BE1-CDS220 

Testing And Maintenance 

13-1 

SECTION 13 

•

 TESTING AND MAINTENANCE 

GENERAL 

The need to test protective relays to confirm performance as designed by relay manufacturers will always 
exist. This Section provides guidelines for performing those tests and others. It also provides guidelines 
for performing maintenance on, and troubleshooting the BE1-CDS220 relay. Included are discussions on 
testing philosophies and methods, requirements, and expected outcomes. For assistance in conducting 
relay self-tests and troubleshooting using internal diagnostics, contact Basler Electric, Customer Service. 

TESTING PHILOSOPHIES 

Testing is generally divided into several categories and is known by various names: 

•

 

Acceptance (or integrity) 

•

 Commissioning 

•

 

Periodic (or maintenance) 

•

 Functional 

(application) 

•

 Performance 

While all types of tests may be performed, they are not generally performed by all users. Likewise, the 
degree to which you will conduct each type of test depends on need, economics, and perceived system 
value.   

Acceptance Testing 

Acceptance (or integrity) testing is intended to confirm through basic tests, that a particular relay that has 
been manufactured and shipped meets published core specifications. Some of the more rudimentary 
procedures will provide a good foundation for application-specific tests that may be delved into during 
functional or commissioning tests. Generally, while basic in nature, these tests validate proper relay 
manufacturing and shipping and usually precede any functional or commissioning tests. 

Basler Electric performs detailed acceptance testing on all devices to verify all functions meet published 
specifications. All products are packaged and shipped using strict standards and will remain intact and 
precise during shipping. The BE1-CDS220 relay is a microprocessor-based relay whose operating 
characteristics will not change over time. The relay will not experience changes in operating 
characteristics during transit. However, it remains material that you perform these basic acceptance tests 
to verify the device has not suffered any degradation in transit. Basler Electric warrants all products 
against any decay in performance outside of the published specified tolerances that result from problems 
created during transit.   

Commissioning Testing 

Commissioning testing verifies all physical connections and functional aspects of the protective relay for a 
new installation. All of the following connections or functions can be verified during commissioning tests:  

•

 

Proper connection and sensing of current and voltage signals as applicable 

•

 

Connections of I/O contacts 

•

 

I/O sensing versus virtual sensing 

•

 Setting 

validation 

•

 

Proper operation of equipment (main or auxiliary) 

•

 

Proper alarming (to SCADA) and/or targeting 

Periodic Testing 

Periodic (or maintenance) testing can be performed at regularly scheduled intervals or upon an indication 
of problems or questionable operations within the relay. Verifying the integrity of the relay performance 
(short of playback of recorded events) may be necessary by performing certain tests similar to those 
accomplished in the acceptance and/or functional tests. Verification that the relay is measuring signals 

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

Eaton Cutler-Hammer D64RP18 Instruction Manual preview
Cutler-Hammer D64RP18
Бренд: Eaton Страницы: 17
Chenzhu CZ3383.11 User Manual preview
CZ3383.11
Бренд: Chenzhu Страницы: 2
SiKom EGR-1 Installation And User Manual preview
EGR-1
Бренд: SiKom Страницы: 4
GE MFAC 14 User Manual preview
MFAC 14
Бренд: GE Страницы: 25
GE MLJ Manual preview
MLJ
Бренд: GE Страницы: 42
GE MDP Instruction Manual preview
MDP
Бренд: GE Страницы: 68
GE MOV 2000 Instructions Manual preview
MOV 2000
Бренд: GE Страницы: 78
GE MOTOR MANAGEMENT RELAY 469 Instruction Manual preview
MOTOR MANAGEMENT RELAY 469
Бренд: GE Страницы: 311
GE MiCOM P40 Agile P14D Manual preview
MiCOM P40 Agile P14D
Бренд: GE Страницы: 12
Siemens SIRIUS 3RS1000 Operating Instructions Manual preview
SIRIUS 3RS1000
Бренд: Siemens Страницы: 6
Siemens SIRIUS 3RS1040 Operating Instructions Manual preview
SIRIUS 3RS1040
Бренд: Siemens Страницы: 8
Siemens SIRIUS 3RS1042 Operating Instructions Manual preview
SIRIUS 3RS1042
Бренд: Siemens Страницы: 8
Siemens CRM-4 Installation Instructions preview
CRM-4
Бренд: Siemens Страницы: 4
Siemens 7UG0583-1CU20 Operating Instructions preview
7UG0583-1CU20
Бренд: Siemens Страницы: 4
Siemens BD2-AK03X/FS Series Installation Instructions Manual preview
BD2-AK03X/FS Series
Бренд: Siemens Страницы: 8
LEGRAND RTX Series Technical Data Sheet preview
RTX Series
Бренд: LEGRAND Страницы: 5
ABB SSV-T Instruction Leaflet preview
SSV-T
Бренд: ABB Страницы: 12
Eaton EMR-3MP0 Installation, Operation And Maintenance Manual preview
EMR-3MP0
Бренд: Eaton Страницы: 281

Бренды по названию

Популярные бренды

Загрузить еще бренды