manualshive.com logo in svg

Texas Instruments MSP430FR58 Series, User Manual

The Texas Instruments MSP430FR58 Series offers an advanced range of microcontrollers for various applications. Enhance your user experience with our comprehensive User Manual, available for free download from manualshive.com. This manual provides in-depth insights on utilizing the full potential of your MSP430FR58 device.

Share
Download
background image

www.ti.com

SDHS Registers

599

SLAU367P – October 2012 – Revised April 2020

Submit Documentation Feedback

Copyright © 2012–2020, Texas Instruments Incorporated

Sigma-Delta High Speed (SDHS)

Table 22-14. SDHSRIS Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

3

DTRDY

R

0h

SDHS Data Ready Raw Interrupt Status bit. Read Only. This bit is
asserted when a new conversion data is available in the data buffer
and remains set as long as the buffer is not empty regardless of the
SDHS data conversion status.

Note: the data buffer is automatically cleared when the data buffer
becomes empty.

Following two methods can be used to empty the data buffer after
completing data conversion if necessary:

1) When the DTC is enabled, no additional action is required. The
DTC reads the data buffer until the data buffer becomes empty.

2) When the DTC is disabled, then either read the SDHSDT register
until this bit is cleared or enable the DTC so that the DTC empties
the buffer. Either way, this bit will be cleared when the buffer
becomes empty.

Reset type: PUC

0h (R) = No DTRDY event

1h (R) = The data buffer has become empty.

2

SSTRG

R

0h

SDHS Conversion Start Trigger Raw Interrupt Status bit. Read Only.

Reset type: PUC

0h (R) = No SSTRG event

1h (R) = Converson Start signal has been asserted

1

ACQDONE

R

0h

Acquisition Done Raw Interrupt Status bit. Read Only. This bit is not
de-asserted by hardware. This bit is asserted when data conversion
is ended (either complete or incomplete).

If SDHSCTL2.DTOFF = 0, then this bit is asserted when data buffer
becomes empty (i.e. when DTC completes the data transfer).

If SDHSCTL2.DTCOFF = 1, then this bit is asserted immediately
when data conversion stops regardless of the data buffer status. In
this case, CPU can continuously read the SDHSDT register until the
data buffer becomes emtpy.

Reset type: PUC

0h (R) = No ACQDONE event

1h (R) = Data conversion has been finished (either complete or
incomplete).

0

OVF

R

0h

SDHS Data Overflow Raw Interrupt Status bit. Read Only. This bit is
not automatically de-asserted by hardware.

Reset type: PUC

0h (R) = No OVF event

1h (R) = When DTC is enabled (SDHSCTL2.DTCOFF = 0), DTC has
dropped at least one sample. This indicates that the system clock
needs to be increased.

When DTC is disabled (SDHSCTL2.DTCOFF = 1), At least one new
sample has been overwritten to SDHSDT register before the
previous value is read.

Summary of Contents for MSP430FR58 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSP430FR58 Series

ON Semiconductor MT9M034 User Manual preview
MT9M034
Brand: ON Semiconductor Pages: 5
MSI MS-7277 Instruction Manual preview
MS-7277
Brand: MSI Pages: 94
MSI MS-6319 Manual preview
MS-6319
Brand: MSI Pages: 76
Texas Instruments TPS61090EVM-029 User Manual preview
TPS61090EVM-029
Brand: Texas Instruments Pages: 19
DFI BT253 User Manual preview
BT253
Brand: DFI Pages: 62
MSI K9N6PGM2-V2 - Motherboard - Micro ATX User Manual preview
K9N6PGM2-V2 - Motherboard - Micro ATX
Brand: MSI Pages: 153
Analog Devices AD9741 Quick Start Manual preview
AD9741
Brand: Analog Devices Pages: 6
Commell LV-678 User Manual preview
LV-678
Brand: Commell Pages: 53
Texas Instruments INA2180-2181 User Manual preview
INA2180-2181
Brand: Texas Instruments Pages: 20
Renesas ISL9122AIIN-EVZ Manual preview
ISL9122AIIN-EVZ
Brand: Renesas Pages: 17
Gigabyte GA-C847N-D User Manual preview
GA-C847N-D
Brand: Gigabyte Pages: 44
IEI Technology NOVA-PV-D4251 User Manual preview
NOVA-PV-D4251
Brand: IEI Technology Pages: 194
Supero X8DA3 User Manual preview
X8DA3
Brand: Supero Pages: 97
Pericom PI2EQX6804-A User Manual preview
PI2EQX6804-A
Brand: Pericom Pages: 8
Aaeon GENE-9455 Rev.B Manual preview
GENE-9455 Rev.B
Brand: Aaeon Pages: 64
Gigabyte GA-H97N User Manual preview
GA-H97N
Brand: Gigabyte Pages: 80
Gigabyte GA-EP45T-DS3 User Manual preview
GA-EP45T-DS3
Brand: Gigabyte Pages: 116
Epson S5U12517P00C100 User Manual preview
S5U12517P00C100
Brand: Epson Pages: 24

Brands by name

Popular brands

Load more brands