manualshive.com logo in svg

NXP Semiconductors LCP43 Series, User Manual

Share
Download
NXP Semiconductors LCP43 Series User Manual Download Page 355

UM10503

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2012. All rights reserved.

User manual

Rev. 1.3 — 6 July 2012 

355 of 1269

NXP Semiconductors

UM10503

Chapter 18: LPC43xx Serial GPIO (SGPIO)

 

18.6.2 SGPIO multiplexer configuration registers (SGPIO_MUX_CFG0 to 15)

Each register controls one SGPIO multiplexer to select the following sources:

•

External clock source (when COUNT is not used)

•

External clock qualifier (static or controlled by a slice or external pin)

•

Input concatenation structure

SGPIO_MUX_CFG0 to SGPIO_MUX_CFG15 control slices A (register 0) to P (register 
15).

To avoid oscillation, slices that can be a clock source for other slices cannot support 
external slice clocks themselves (CLK_SOURCE_SLICE_MODE). These slices should 
not feed a clock higher than SGPIO_CLOCK/2 to the other slices.

 

Fig 35. SGPIO local output pin multiplexer configuration

 

p_out_c fg

dout _doutm1

dout _doutm2

dout _doutm4

dout _doutm8

GP IO_RE G

c lk_out

p_oe_c fg

GP IO _OE RE G

dout_oem2

dout_oem4

dout_oem8

OUT_MUX _CFGx

doe

dout

5:4

3:0

dout_oem1

00

01

10

11

0000

00x x

01x x

10x x

0100

1000

11x x

p_oe_c fg

6

0

1

res erv ed

Table 215. SGPIO multiplexer configuration registers (SGPIO_MUX_CFG0 to 15, addresses 

0x4010 0040 to 0x4010 007C) bit description

Bit

Symbol

Value Description

Reset 
value

Access

0

EXT_CLK_ENABLE

Select clock signal.

0

R/W

0x0

Internal clock signal (slice)

0x1

External clock signal (pin)

Summary of Contents for LCP43 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands