Huawei FusionCol8000-E24 User Manual Download Page 24

Page: 24 / 269

No.

Item

Description

Outdoor

exhaust

fan

● A Huawei-developed high-speed fan is used, which

features large air volume, high static pressure, high

reliability, and a long service life.

● The fan is separated from the drive. The fan efficiency is

improved by more than 8% compared with a common EC

fan.

● The direct drive that the fan adopts has higher

transmission efficiency than the belt drive, which reduces

belt replacement and routine checks.

Evaporat

The synergy field principle and computational fluid dynamics

(CFD) are used to optimize the flow path design, greatly

improving the heat exchange efficiency. The evaporator air

flow organization is more reasonable, and the air resistance

is smaller.

Spray

pump

● A horizontal three-stage centrifugal pump is used, which

features high pump lift, small size, high reliability, and

long service life.

● The water pump is made of new lubrication sealing

material. Wear parts such as water pump spindle seal and

seal ring do not need to be maintained in the life cycle.

● The variable-frequency drive power supply mode is used

to implement soft startup of the water pump, improving

the pump reliability.

Indoor

air

supply

fan

● A Huawei-developed high-speed fan is used, which

features large air volume, high static pressure, high

reliability, and a long service life.

● The fan is separated from the drive. The fan efficiency is

improved by more than 8% compared with a common EC

fan.

● The direct drive that the fan adopts has higher

transmission efficiency than the belt drive, which reduces

belt replacement and routine checks.

Compres

sor

● The FusionCol8000-E uses a DC variable-frequency

compressor that features compact size, light weight, a

long service life, low noise, easy installation, high

reliability, stability, and energy efficiency.

● The high-precision drive automatically adapts to the

system pressure fluctuations.

● The drive conducts precision self-check. Compressor and

drive faults are separated.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

2 Product Description

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands