Huawei FusionCol8000-E24 User Manual Download Page 87

Page: 87 / 269

Figure 5-7 Installing an air duct

(1) Indoor return air duct

(end)

(2) Indoor supply air duct

(3) Indoor return air duct

(side)

NO TE

● The air duct must be wrapped with thermal insulation foam, and the thickness of the

thermal insulation foam must be greater than or equal to 3 cm.

● The joint between the air duct and the unit should be sealed to prevent air leakage.

Generally, the sealing cotton is pressed inside the flange of the air duct or sealant is

applied to the flange after installation.

----End

5.4.5 Installing Pipes

The designed height of the water trap must meet the requirements specified in

Figure 4-10

Figure 5-8 Designed height of the water trap

NO TE

It is recommended that the height of segment B be as low as possible.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

5 System Installation (FDC Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands