manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

5.5.3 Cable Routes

Figure 5-18 Cable routes

(1) Power cable

(2) Signal cable

5.5.4 (Optional) Installing Teamwork and Monitoring

Communications Cables

NO TICE

● Smart cooling products of different models and software versions cannot be

networked for teamwork.

● Connect teamwork and monitoring communications cables based on the

networking scenario.

● The teamwork communications cable must be a shielded network cable of Cat

5e or higher specifications. The network cable length between adjacent units

must be less than or equal to 100 m, and the maximum distance for CAN

teamwork communication must be less than or equal to 310 m.

● Route cables in compliance with local standards. Take appropriate shielding

measures, such as using a galvanized pipe or an ELV cable tray, to reduce the

impact of electromagnetic interference on teamwork communication.

Otherwise, teamwork networking may fail.

5.5.4.1 Preparing a Network Cable

Step 1 Crimp a network cable.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

5 System Installation (FDC Scenario)

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

85

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Fakir CLYDE Instructions For Use Manual preview
CLYDE
Brand: Fakir Pages: 40
Fagor VCE-1500SC Safety Regulations preview
VCE-1500SC
Brand: Fagor Pages: 5
PALSON NILO Manual preview
NILO
Brand: PALSON Pages: 46
Zanotti GS Series Use And Maintenance Instructions preview
GS Series
Brand: Zanotti Pages: 84
W.Tech RAA Series Installation And Maintenance Manual preview
RAA Series
Brand: W.Tech Pages: 16
Argo AWI726HL Technical Data & Service Manual preview
AWI726HL
Brand: Argo Pages: 38
Kärcher A 1001 Operating Instructions Manual preview
A 1001
Brand: Kärcher Pages: 51
Klimaire KSIO User Manual preview
KSIO
Brand: Klimaire Pages: 16
Magio MG-892 Instruction Manual preview
MG-892
Brand: Magio Pages: 28
Turbo Air TAS-36EHU Owner'S Manual preview
TAS-36EHU
Brand: Turbo Air Pages: 19
Tiger MEA-A Instructions Manual preview
MEA-A
Brand: Tiger Pages: 6
Ducasa MULTI INV 183 E Installation Instruction preview
MULTI INV 183 E
Brand: Ducasa Pages: 8
INNOLIVING PROFESSIONAL XL INN-560 User Manual preview
PROFESSIONAL XL INN-560
Brand: INNOLIVING Pages: 28
Klimaire KSIF009-H115-I Service Manual preview
KSIF009-H115-I
Brand: Klimaire Pages: 82
Amano Pioneer Eclipse 250AP115 Operator'S Manual preview
Pioneer Eclipse 250AP115
Brand: Amano Pages: 64
Hoover SteamVac deluxe Owner'S Manual preview
SteamVac deluxe
Brand: Hoover Pages: 16
Friedrich KP05 Installation And Operation Manual preview
KP05
Brand: Friedrich Pages: 15
Midea MAW08V1QWT User Manual preview
MAW08V1QWT
Brand: Midea Pages: 72

Brands by name

Popular brands

Load more brands