manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

●

All cable holes should be sealed. Seal the used cable holes with firestop putty.

Seal the unused cable holes with the caps delivered with the cabinet. The

following figure shows the criteria for correct sealing with firestop putty.

●

Do not scrawl, damage, or block any warning label on the equipment.

●

When installing the equipment, use a torque wrench with a proper range to

tighten the screws. When using a wrench to tighten the screws, ensure that

the wrench does not tilt and the torque error does not exceed 10% of the

specified value.

●

Do not work with power on during installation.

●

Repaint any paint scratches caused during equipment transportation or

installation in a timely manner. Equipment with scratches cannot be exposed

to an outdoor environment for an extended period of time.

●

Before operations, ensure that the equipment is firmly secured to the floor or

other solid objects, such as a wall or an installation rack.

●

Do not use water to clean electrical components inside or outside of a

cabinet.

●

Do not change the structure or installation sequence of equipment without

permission.

●

Do not touch a running fan with your fingers, components, screws, tools, or

boards before the fan is powered off or stops running.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

1 Safety Information

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

3

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Panasonic U-16GE2E5 Procedures And Technical Points For System Installation preview
U-16GE2E5
Brand: Panasonic Pages: 21
Galletti ESTRO FA Installation, Use And Maintenance Manual preview
ESTRO FA
Brand: Galletti Pages: 20
Magic-Pak EWC V Series Installation Instructions preview
EWC V Series
Brand: Magic-Pak Pages: 5
Danby AAC5246DE Use And Care Manual preview
AAC5246DE
Brand: Danby Pages: 12
Zepter Therapy Air Smart TAS-100 Instruction Manual preview
Therapy Air Smart TAS-100
Brand: Zepter Pages: 9
Larson Electronics IND-AHC-TRF-2X2-UVC-R1-120V Instruction Manual preview
IND-AHC-TRF-2X2-UVC-R1-120V
Brand: Larson Electronics Pages: 3
Soleus Air iCongo PSQ-08-01 Operating Instructions Manual preview
iCongo PSQ-08-01
Brand: Soleus Air Pages: 18
Clatronic AKS 825 Instruction Manual preview
AKS 825
Brand: Clatronic Pages: 41
York 19 SEER Installation Manual preview
19 SEER
Brand: York Pages: 26
Alfa Network Optigo CC Instruction Manual preview
Optigo CC
Brand: Alfa Network Pages: 28
Dirt Devil featherlite Carpet Shampooer Operating, And Servicing Instructions preview
featherlite Carpet Shampooer
Brand: Dirt Devil Pages: 36
Vax SlimVac TBTTV1D1 Manual preview
SlimVac TBTTV1D1
Brand: Vax Pages: 20
Kooltronic Hazardous Location HL Series Operator'S Manual preview
Hazardous Location HL Series
Brand: Kooltronic Pages: 19
Shop-Vac 3942010 User Manual preview
3942010
Brand: Shop-Vac Pages: 36
Black + Decker BPT05WTB Instruction Manual preview
BPT05WTB
Brand: Black + Decker Pages: 84
Uberhaus 87795012 Operator'S Manual preview
87795012
Brand: Uberhaus Pages: 30
Johnson Pulito Instructions For Use Manual preview
Pulito
Brand: Johnson Pages: 32
Rowenta DR91 Series Manual preview
DR91 Series
Brand: Rowenta Pages: 81

Brands by name

Popular brands

Load more brands