manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

Step 6 Flip the clip to lock the fan drive.

Figure 12-42 Installing the fan drive

Step 7 Power on the unit, and choose Maint > Wizard Startup on the home screen. Start

the fan and check that the fan works properly without any alarms. Check that the

smart cooling product works properly before you exit.

----End

12.19 Replacing a Liquid Level Sensor

Prerequisites

●

A liquid level sensor needs to be replaced.

●

A spare liquid level sensor of the same model is available and functional.

●

Tool: solid wrench

Context

The liquid level sensor can be maintained only at the water tank.

Procedure

Step 1 On the home screen of the display module, tap Shutdown and turn off the unit

switch in the PDF.

NO TICE

Exercise caution because the unit is still energized after it is shut down on the

home screen of the display module.

Step 2 Open the maintenance door.

Step 3 Replace the liquid level sensor in the spray water tank.

●

Open the water tank cover.

●

Cut off the cable tie that secures the liquid level sensor cable, and remove the

interconnection terminal.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

12 Component Replacement

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

192

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Vaillant VAI 6-025 WN User Manual preview
VAI 6-025 WN
Brand: Vaillant Pages: 136
Vax Air3 Agile Quick Start Manual preview
Air3 Agile
Brand: Vax Pages: 2
Vax Rapide Spring Clean VCWRS700 User Manual preview
Rapide Spring Clean VCWRS700
Brand: Vax Pages: 11
Daikin Super Multi NX FHQ35BVV1B Installation Manual preview
Super Multi NX FHQ35BVV1B
Brand: Daikin Pages: 30
ECG VP 3120 S Instruction Manual preview
VP 3120 S
Brand: ECG Pages: 84
Elba ELBA12HAN20 Operation Manual preview
ELBA12HAN20
Brand: Elba Pages: 20
Impecca IWA25-QS30 User Manual preview
IWA25-QS30
Brand: Impecca Pages: 44
Serene House ODEUR DE CHINE II Instruction Manual preview
ODEUR DE CHINE II
Brand: Serene House Pages: 6
H-P Products TURBINE POWERHEAD and HAND HELD TURBINE... Instruction Manual preview
TURBINE POWERHEAD and HAND HELD TURBINE...
Brand: H-P Products Pages: 10
Daewoo RC-230R Owner'S Manual preview
RC-230R
Brand: Daewoo Pages: 12
Uberhaus MWK-15CRN1-BJ7 User Manual preview
MWK-15CRN1-BJ7
Brand: Uberhaus Pages: 29
Acson 5CEY15E Installation Manual preview
5CEY15E
Brand: Acson Pages: 140
Yamato U-match Series Owner'S Manual preview
U-match Series
Brand: Yamato Pages: 68
Disan DS A01 Owner'S Manual preview
DS A01
Brand: Disan Pages: 22
Radialight AER Pro Operating Instructions Manual preview
AER Pro
Brand: Radialight Pages: 16
gmc aircon GMCAB15 User Manual preview
GMCAB15
Brand: gmc aircon Pages: 10
EnviroAire IAQ UV-C Replacement Manual preview
IAQ UV-C
Brand: EnviroAire Pages: 3
Crosley 2020213A0870 Use & Care Manual preview
2020213A0870
Brand: Crosley Pages: 9

Brands by name

Popular brands

Load more brands