Huawei FusionCol8000-E24 User Manual Download Page 116

Page: 116 / 269

Tab

Parameter

Description

Balance of water and

electricity

consumption

This parameter can be set to Power

saving mode, Normal water saving

mode, Extreme water saving mode,

or Customized mode. Set this

parameter based on the site

requirements.

NOTE

You are advised to retain the default value.

Wet mode startup

temperature

This parameter is displayed when

Balance of water and electricity

consumption is set to Customized

mode.
Set this parameter as required.

Dehumidifying

function

● Enable: The device starts

dehumidifying when the ambient

humidity is higher than the

humidity setpoint.

● Disable: The dehumidifying function

is disabled.

DO_1 action

This parameter can be set to On or

Off, and is used together with DO_1.

For details, see DO_1 description.

DO_2 action

This parameter can be set to On or

Off, and is used together with DO_2.

For details, see DO_2 description.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

107

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands