Huawei FusionCol8000-E24 User Manual Download Page 222

Page: 222 / 269

Step 4 Insert the positive pressure tube of the differential pressure gauge into the unit

through the cable hole for about 30 mm.

Figure 13-14 Pressure measurement points

(1) Pressure measurement point for the

negative pressure tube

(2) Pressure measurement point for the

positive pressure tube

NO TE

The cross section of the pressure tubes must be perpendicular to the wind direction.

Step 5 Start the unit, set the indoor fan speed to the maximum value, and read the

pressures measured at the positive and negative pressure points.

NO TE

Choose Maint > Diagnostic Mode > Enter and set the indoor fan speed to the maximum

value.

Step 6 Tap Start on the home screen. Ensure that the unit is running normally without

any alarms.

Step 7 Log in to the WebUI as user admin, choose Settings > System Settings > System

Control > Advanced, and set Static pressure.

Step 8 Choose Running > Status Summary and view the value of air volume.

NO TE

● Static pressure setting = Pressure measured at the positive pressure point – Pressure

measured at the negative pressure point.

● User operator can access customer and delivery parameters. The parameters on the

Advanced menu are delivery parameters. User admin can access customer, delivery,

maintenance, and R&D parameters. The parameters on the Advanced menu are R&D

parameters.

● To prevent the effect of misoperations on the system, log in as user operator before

modifying parameters. Confirm with Huawei technical support before modifying

parameters which cannot be modified by user operator. Otherwise, Huawei will not be

liable for any consequences of the modification performed by the user.

● Only certified professionals are allowed to modify advanced parameters of the unit.

Unauthorized modifications can result in unit malfunction and even damage.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

13 FAQ

213

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands