Huawei FusionCol8000-E24 User Manual Download Page 154

Page: 154 / 269

Fault

Type

Possible Cause

Solution

A short circuit exists

between the fan and

the ground.

Check the power cable and voltage of the

motor.

The coil is short-

circuited or the

motor is burnt.

Replace the fan. If there is a beam for

hoisting the fan in the air exhaust section,

before removing the fan, use a hook to

secure the fan to the beam to prevent the

fan from falling.

The overtemperature

protection function

of the motor is

triggered (the motor

is overheated).

Check whether the air circulation is normal.

Clear foreign matters if necessary.

The fan blade is blocked or dirty.

Check the ambient temperature of the fan.

Check the voltage.

The fan blade is

blocked or dirty.

Power off the motor and prevent it from

being connected again.
● Check whether the motor is powered off.
● Clear foreign matters or contaminants.

The airflow direction

is incorrect (the

direction of the

motor is opposite to

that of the high-

speed airflow).

Check the airflow direction (rotation caused

by airflow reversal).

The fan

rotates

slowly.

Fan blade friction/

collision

Clear foreign matters or dirt in the fan if

necessary.

The active

temperature

management

function is enabled

(when the motor or

electronic system is

overheated).

Check whether the air circulation is normal.

Clear foreign matters if necessary.

The fan blade is blocked or polluted.

Check the ambient temperature of the fan.

Check the installation space (air speed

above the heat source).

The

airflow

volume is

insufficien

The fan rotates

slowly.

Check whether the fan rotates slowly.

The air channel is

blocked.

Check whether the airflow is smooth

(intake/exhaust air damper and air filter).

The fan blade is blocked or polluted.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

10 Troubleshooting

145

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands