Huawei FusionCol8000-E24 User Manual Download Page 28

Page: 28 / 269

Name

Description

Air supply

fan

● A Huawei-developed high-speed fan is used, which

features large air volume, high static pressure, high

reliability, and a long service life.

● The fan is separated from the drive. The fan efficiency is

improved by more than 8% compared with a common EC

fan.

● The direct drive that the fan adopts has higher

transmission efficiency than the belt drive, which reduces

belt replacement and routine checks.

Compresso

● The FusionCol8000-E uses a DC variable-frequency

compressor that features compact size, light weight, a

long service life, low noise, easy installation, high

reliability, stability, and energy efficiency.

● The high-precision drive automatically adapts to the

system pressure fluctuations.

● The drive conducts precision self-check. Compressor and

drive faults are separated.

Compresso

r drive

● The variable-frequency compressor drive, water pump

drive, and 24 V power module are integrated into one

device to save space in the smart cooling product and

improve efficiency.

● The compressor drive is controlled over RS485. You can

view the drive running status and parameters on the

display module in real time to facilitate fault locating.

Liquid

level

sensor

● Liquid level sensor (at the bottom of the precooling

module): A high liquid level sensor is added under the

precooling module. If the precooling module is abnormal,

an alarm is generated in advance.

● Liquid level sensor (inside the spray water tank): There are

three liquid level sensors in the spray water tank, which

are associated with the water refill and drainage systems.

If the water level in the water tank is lower than the low

liquid level sensor, water refill starts. If the water level in

the water tank is higher than the high liquid level sensor,

water refill stops. If the water level in the water tank is

higher than the overflow water level sensor, an alarm is

generated and water is drained.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

2 Product Description

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands