Huawei FusionCol8000-E24 User Manual Download Page 211

Page: 211 / 269

FAQ

13.1 Operations with a USB Flash Drive

Context

After connecting a USB flash drive to the USB port on the main control module,

you can export data, import and export configuration files, and import certificates

and keys.

NO TICE

● You are advised to use the FAT32 USB flash drive with a capacity less than or

equal to 64 GB. For a non-FAT32 USB flash drive, format it to the FAT32 format

using a computer.

● Before using a USB flash drive, ensure that its data has been scanned by

antivirus software and is secure.

Procedure

Step 1 Connect a USB flash drive.

Figure 13-1 Connecting to a USB flash drive

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

13 FAQ

202

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands