Huawei FusionCol8000-E24 User Manual Download Page 77

Page: 77 / 269

5.1.2 Space Requirements

Install the unit strictly according to the design drawing and reserve space for

maintenance and ventilation.

Figure 5-1 Maintenance space (not combined) (unit: mm)

(1) Wall

(2) Indoor air return vent (end)

(3) Electric control box

(4) Corridor module

Figure 5-2 Maintenance space (combined) (unit: mm)

(1) Wall

(2) Indoor air return vent (end)

(3) Electric control box

(4) Corridor module

5.1.3 Storage Requirements

Before installing the unit, place it in a dry, rainproof, fireproof, and anticorrosive

environment.

●

If the unit is installed outdoors, ensure that it is free from dirt, rain, snow, or

animal intrusion, and that the protective film on the surface is intact.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

5 System Installation (FDC Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands