manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

Symptom

Possible Cause

Solution

The drainpipe does not have

a water trap or does not

meet the requirements.

Install or adjust the water

trap.

The fan works

abnormally.

The fan bearing is worn out.

Repair or replace the bearing.

The fan blade is interfered

with the shell.

Adjust the fan blade.

There is foreign matter.

Clear foreign matter.

The air volume

is excessively

large.

The external static pressure is

excessively small (the air

duct is excessively short).

Balance the air volume and

air pressure.

The fan motor

is burnt out.

The motor is overloaded.

Balance the air volume and

replace the fan.

The motor is poorly

insulated.

Replace the fan.

The running

sound is

abnormal.

The compressor, fan, or pipes

are loose.

Check and secure loose parts.

The air damper is shaking.

Adjust the air damper.

The compressor

does not work.

The high-pressure switch is

triggered.

Check the high-pressure

switch.

The circuit breaker, fuse, or

cable is disconnected.

Check the main circuit

breaker, compressor circuit

breaker, fuses, and cables.

The compressor motor is

damaged.

Check whether the motor is

damaged and needs to be

replaced.

The compressor does not

need to be started.

Check the requirement status

on the display module.

The drive is faulty.

Replace the drive.

The compressor

discharge

temperature is

too high.

The refrigerant loop or

component is blocked.

Clean up foreign matter in

the refrigerant loop.

Air enters the refrigerant

loop.

Exhaust air and repair the

pipeline.

Heat dissipation is poor

because the condenser is

dirty or blocked.

Clean the condenser fins.

The exhaust fan is faulty.

Check whether the exhaust

fan works properly.

The refrigerant is insufficient. Charge more refrigerant.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

10 Troubleshooting

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

148

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Vax S2 Series User Manual preview
S2 Series
Brand: Vax Pages: 12
Vax VX1 Instruction Manual preview
VX1
Brand: Vax Pages: 9
NANO 2 Series Maintenance Service Manual preview
2 Series
Brand: NANO Pages: 28
GE AGP07 Owner'S Manual & Installation Instructions preview
AGP07
Brand: GE Pages: 32
GE AHM18DP Owner'S Manual And Installation Instructions preview
AHM18DP
Brand: GE Pages: 32
GE AGL05 Owner'S Manual preview
AGL05
Brand: GE Pages: 20
GE AGH08 Owner'S Manual & Installation Instructions preview
AGH08
Brand: GE Pages: 16
GE AEM14 Series Owner'S Manual And Installation Instructions preview
AEM14 Series
Brand: GE Pages: 52
GE AEQ24 Owner'S Manual And Installation Instructions preview
AEQ24
Brand: GE Pages: 56
GE AJCQ10DCD Series Owner'S Manual And Installation Instructions preview
AJCQ10DCD Series
Brand: GE Pages: 16
GE AJCM10ACD User Manual preview
AJCM10ACD
Brand: GE Pages: 24
GE AJCM08ACD Owner'S Manual And Installation Instructions preview
AJCM08ACD
Brand: GE Pages: 24
GE AJCQ10ACC Owner'S Manual And Installation Instructions preview
AJCQ10ACC
Brand: GE Pages: 76
GE AJCH08ACC Datasheet preview
AJCH08ACC
Brand: GE Pages: 3
Daikin FVXG25K2V1B Technical Data Manual preview
FVXG25K2V1B
Brand: Daikin Pages: 12
Daewoo RC-108 Owner'S Manual preview
RC-108
Brand: Daewoo Pages: 5
QuietFlo 30401 User Manual preview
30401
Brand: QuietFlo Pages: 24
Lakeland 23307 User Manual preview
23307
Brand: Lakeland Pages: 16

Brands by name

Popular brands

Load more brands