Huawei FusionCol8000-E24 User Manual Download Page 66

Page: 66 / 269

Figure 4-22 Connecting communications cables

----End

4.5.4.4 FE Te RS485 Monitoring

Step 1 Connect teamwork and monitoring communications cables.

Networking

FE Teamwork

RS485 Monitoring

Protocol

MAC_CAN

Modbus-RTU

Note

A teamwork network supports

a maximum of 16 units.

It takes 3 x

seconds to

collect data from

units. If

the time required for the host

to collect data from all units

does not meet the

performance requirements,

group the units.
● If units are not grouped (

= 1), set RS485 monitoring

grouping to Enable on the

Modbus Settings screen

for each unit.

● If units are grouped (

> 1;

recommended:

≤ 4), set

RS485 monitoring

grouping to Enable on the

Modbus Settings screen

for the unit with the

COM/FE port connected.

Retain the default setting

(Disable) for other units.

NO TE

● Connect the COM/FE port on the main control module of the last unit in each group to

the RS485 port on the host.

● Customers can purchase an ECC and NetEco as the monitoring system.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands