Huawei FusionCol8000-E24 User Manual Download Page 48

Page: 48 / 269

4.3.2 Cables

NO TICE

● The cable diameter must comply with local cable standards. The factors that

affect cable selection include the rated current, cable type, routing mode,

ambient temperature, and maximum expected line loss.

● Waterproof connectors for cables should be designed according to the

recommended cable specifications in the following table. If a cable used onsite

does not meet the recommended specifications, the cable may fail to be routed

through the waterproof connector or the waterproof connector may fail to be

secured.

● The onsite grounding resistance must comply with related standards.

Table 4-3 Cables

Item

Recommended Specifications

Power cable

Active power input: 3 x 70 mm

(L1/L2/L3) + 35 mm

(PE)

Standby power input: 3 x 70 mm

(L1/L2/L3) + 35 mm

(PE)

(Optional) T/H

sensor cable, water

sensor (rope type),

and teamwork and

monitoring

communications

cable

CAT 5e or higher shielded network cable

Equipotential

ground lug/ground

cable

● Ground lug: Use hot-dip zinc-coated flat steel sheet

with a cross-sectional area greater than or equal to 50

● Ground cable: Use equipotential ground cables with a

cross-sectional area of at least 16 mm

and route the

ground cables through a plastic-coated metal hose.

4.4 Installing a Unit

4.4.1 Unpacking and Checking

Context

Move the unit closest to the installation position before unpacking it to facilitate

movement and avoid damage.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands