manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

Context

NO TICE

Before checking and maintaining the device, ensure that the primary power supply

to the device is disconnected and the drive has been powered off for 10 minutes.

Otherwise, electrical shocks may occur.

Procedure

Step 1 On the home screen of the display module, tap Shutdown and turn off the unit

switch in the PDF.

NO TICE

Exercise caution because the unit is still energized after it is shut down on the

home screen of the display module.

Step 2 Open the maintenance door.
Step 3 Remove all cables from the drive and cut the cable ties using diagonal pliers.
Step 4 Remove the four screws on the drive using a Phillips screwdriver, and pull out the

drive.

Figure 12-40 Removing a drive

Step 5 Install the new drive.
Step 6 Connect the cables to the drive.
Step 7 Power on the unit, and choose Maint > Wizard Startup on the home screen. Start

the compressor and check that the compressor works properly without any alarms.

Check that the smart cooling product works properly before you exit.

----End

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

12 Component Replacement

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

190

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Haier AB09CS1ERA Service Manual preview
AB09CS1ERA
Brand: Haier Pages: 60
Salton Platinum Series Instruction Booklet preview
Platinum Series
Brand: Salton Pages: 12
Haier ESAD4089 Manual De Usuario preview
ESAD4089
Brand: Haier Pages: 26
TurboTronic TT-VS777 Instruction Manual preview
TT-VS777
Brand: TurboTronic Pages: 88
Airwell May series Installation And Maintenance Instructions Manual preview
May series
Brand: Airwell Pages: 7
Cleanmaxx 08935 Instruction Manual preview
08935
Brand: Cleanmaxx Pages: 44
Samsung AS09A5MA Service Manual preview
AS09A5MA
Brand: Samsung Pages: 30
Samsung AVMXC023B1A-GB User Manual preview
AVMXC023B1A-GB
Brand: Samsung Pages: 52
Samsung HH105EZM Service Manual preview
HH105EZM
Brand: Samsung Pages: 58
Samsung AQ30C1(2)BCD Owner'S Instructions & Installation Manual preview
AQ30C1(2)BCD
Brand: Samsung Pages: 27
Samsung AQ18A1(A2)QE/B Owner'S Instructions Manual preview
AQ18A1(A2)QE/B
Brand: Samsung Pages: 26
Samsung AQ12AA(B)MCF Owner'S Instructions Manual preview
AQ12AA(B)MCF
Brand: Samsung Pages: 28
Samsung AQ09A5(6)MAF Owner'S Instructions Manual preview
AQ09A5(6)MAF
Brand: Samsung Pages: 28
Samsung SH09AW8 Owner'S Instructions Manual preview
SH09AW8
Brand: Samsung Pages: 26
Samsung DH105CAV User Manual preview
DH105CAV
Brand: Samsung Pages: 17
Samsung AM072BXV Series Service Manual preview
AM072BXV Series
Brand: Samsung Pages: 326
Samsung AVMWH020CA0 Installation Manual preview
AVMWH020CA0
Brand: Samsung Pages: 26
Samsung AQ09NSB User Manual preview
AQ09NSB
Brand: Samsung Pages: 1

Brands by name

Popular brands

Load more brands