Huawei FusionCol8000-E24 User Manual Download Page 128

Page: 128 / 269

Parameter

Description

Percentage of units

allowed to dehumidify

in this group

Set Percentage of units allowed to dehumidify in

this group based on site requirements.

NOTE

You are advised to retain the default value.

The number of units that perform the

dehumidification function is controlled to prevent all

units in the group from starting dehumidification at

the same time, thereby avoiding supercooling and

temperature fluctuation in the equipment room.
● Number of units allowed to dehumidify is the

roundup value of Total number of systems in

this group multiplied by Percentage of units

allowed to dehumidify in this group. The units

allowed to dehumidify are automatically deployed

among all running units.

● If the anti-competitive running mode of the

teamwork group is dehumidification, the master

unit sends the anti-competitive running flag

whose value is dehumidification allowed to the

units allowed to dehumidify.

Rotation function

Indicates whether to allow the smart cooling

products to work as the standby device in turn,

maximizing their service life.

NOTE

It is recommended that the function be enabled when the

load is even.

Rotation period

Number of days for rotation (1–30).

Rotation time

Specifies the start time of rotation for the active and

standby units. 24 time points in a day (0–23).

Forced rotation

Indicates whether to enable forced rotation

regardless of the specified rotation time. After a

forced rotation, the rotation period starts again.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

119

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands