manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

Step 8 Power on the unit and tap Start on the home screen. Ensure that the unit is

running normally without any alarms.

----End

12.10 Replacing an Air Exhaust NTC Temperature

Sensor (FDC Scenario)

Prerequisites

●

An NTC temperature sensor needs to be replaced.

●

A spare NTC temperature sensor of the same model is available and

functional.

●

Tool: Phillips screwdriver

Procedure

Step 1 On the home screen of the display module, tap Shutdown and turn off the unit

switch in the PDF.

NO TICE

Exercise caution because the unit is still energized after it is shut down on the

home screen of the display module.

Step 2 Open the maintenance door.
Step 3 Cut off the cable ties and remove the screws that secure the NTC temperature

sensor.

Step 4 Remove the interconnection terminal from the cable of the NTC temperature

sensor.

Step 5 Install the new NTC temperature sensor, reconnect the cables, and secure the NTC

temperature sensor in the original position.

Step 6 Bind the cable ties.
Step 7 Power on the unit and tap Start on the home screen. Ensure that the unit is

running normally without any alarms.

----End

12.11 Replacing an Air Supply NTC Temperature Sensor

Prerequisites

●

An NTC temperature sensor needs to be replaced.

●

A spare NTC temperature sensor of the same model is available and

functional.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

12 Component Replacement

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

166

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Makita CL183D Technical Information preview
CL183D
Brand: Makita Pages: 7
Dyson DC08 User Manual preview
DC08
Brand: Dyson Pages: 16
Data Aire gForce Ultra Installation, Operation And Maintenance Manual preview
gForce Ultra
Brand: Data Aire Pages: 64
Data Aire gForce Ultra Installation, Operation & Maintenance Manual preview
gForce Ultra
Brand: Data Aire Pages: 123
Olimpia splendid NEXYA S4 User And Installation Manual preview
NEXYA S4
Brand: Olimpia splendid Pages: 154
Olimpia splendid Celsius Instructions For Installation, Use And Maintenance Manual preview
Celsius
Brand: Olimpia splendid Pages: 26
Olimpia splendid Bi2 Series Installation And Manintenance Instructions preview
Bi2 Series
Brand: Olimpia splendid Pages: 100
Olimpia splendid Aquaria Instructions For Installation, Use And Maintenance Manual preview
Aquaria
Brand: Olimpia splendid Pages: 44
Olimpia splendid Unico Easy Manual preview
Unico Easy
Brand: Olimpia splendid Pages: 80
Haier H2SM-14HB03/R2 Operating Manual preview
H2SM-14HB03/R2
Brand: Haier Pages: 57
Panasonic CS-Z20XKEW Service Manual preview
CS-Z20XKEW
Brand: Panasonic Pages: 198
Panasonic S-15MY2E5A CZ-KPY3A Technical Data Manual preview
S-15MY2E5A CZ-KPY3A
Brand: Panasonic Pages: 36
Panasonic CS-RE9QKE Operating Instructions Manual preview
CS-RE9QKE
Brand: Panasonic Pages: 52
Daikin FTXS09JEVJU Operation Manual preview
FTXS09JEVJU
Brand: Daikin Pages: 32
GE ASM12 Owner'S Manual And Installation Instructions preview
ASM12
Brand: GE Pages: 40
Haier HSU-18CI03 Installation Manual preview
HSU-18CI03
Brand: Haier Pages: 8
Makita VC012G Instruction Manual preview
VC012G
Brand: Makita Pages: 148
Midea i5 Extra Instruction Manual preview
i5 Extra
Brand: Midea Pages: 18

Brands by name

Popular brands

Load more brands