Huawei FusionCol8000-E24 User Manual Download Page 183

Page: 183 / 269

12.14 Replacing a Precooling Module

Prerequisites

●

A precooling module needs to be replaced.

●

A spare precooling module of the same model is available and functional.

●

Tools: protective gloves, Phillips screwdriver.

Procedure

Step 1 On the home screen of the display module, tap Shutdown and turn off the unit

switch in the PDF.

NO TICE

Exercise caution because the unit is still energized after it is shut down on the

home screen of the display module.

Step 2 Open the maintenance door to the precooling module.

Figure 12-27 Opening the maintenance door

Step 3 Remove the sheet metal securing the water distributor of the precooling module

and the water pipe, and replace the water distributor as required.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

12 Component Replacement

174

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands