Huawei FusionCol8000-E24 User Manual Download Page 215 | Manualshive

Page: 215 / 269

background image

Step 2 Select Client certificate or Server certificate based on the type of the certificate

in use.

Step 3 Tap Browse next to Upload CA certificate file.
Step 4 Select the CA certificate file to be uploaded.
Step 5 Upload the local certificate file and key file in turn in the same way.
Step 6 Enter Key password and Confirm key password.
Step 7 Tap Submit.

●

If files are imported successfully, a success message will be displayed.

●

If files fail to be imported, a message indicating the cause for failure will be

displayed. Rectify the fault according to the message and import files again.

Step 8 On the home screen, choose Maint > USB Operations > Remove USB to remove

the USB flash drive in safe mode.

----End

13.2 Display Module Screen Operations

13.2.1 How Do I Set LAN Parameters?

If the teamwork networking mode is FE networking, set the LAN parameters

based on the actual situation.

Procedure

Step 1 On the home screen, choose Settings > Comm Settings > LAN IP Settings, and

set LAN IP assigning mode to Manual. Set LAN IP address, LAN subnet mask,

and LAN gateway based on the actual plan.

Figure 13-8 LAN IP Settings

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

13 FAQ

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

206

«
...
213
214
215
216
217
...
»

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Brand: GE Pages: 72

Brand: Samsung Pages: 35

AC TN4PKG Series

Brand: Samsung Pages: 20

EVOLUTION Series

Brand: C&H Pages: 39

Brand: Samsung Pages: 12

Brand: Samsung Pages: 24

Brand: Samsung Pages: 295

AW07A(G)2NBA/DE/EA

Brand: Samsung Pages: 16

Pinguino Air-to-Air PAC EL112CST

Brand: DeLonghi Pages: 8

Brand: Klimaire Pages: 215

Brand: Marvair Pages: 44

Brand: CLIVET Pages: 64

Symphony Solo Series

Brand: YMGI Pages: 48

KACSE 012 TO 144 Series

Brand: ThermoPlus Air Pages: 2

Brand: VIOMI Pages: 18

Brand: WELLTEC Pages: 43

Brand: Daikin Pages: 44

Brand: Beautural Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands