manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

NO TE

Tighten the needle valve bonnets when the charge is complete. Check whether a needle

valve leaks by applying soap bubbles to the valve vent or using a halogen leak detector. If

leakage occurs, contact technical support engineers.

----End

12.15.5 Charging the Remaining Refrigerant

Prerequisites

●

Before starting the compressor, ensure that the unit switch is turned on.

●

Remove the refrigerant cylinder after ensuring that no more refrigerant needs

to be charged.

●

Charge refrigerant in an amount exactly as standard charge required.

Otherwise, the unit may be damaged.

Procedure

Step 1 Tap Start on the home screen.

Step 2 Choose Maint > Diagnostic > Enter to enter the diagnostic mode.

Step 3 Change the compressor rotational speed to 3000 rpm.

Step 4 Open the low pressure valve of the pressure gauge, and charge the remaining

refrigerant from the low pressure needle valve in small flow or intermittently.

Figure 12-37 Charging the remaining refrigerant

(1) Refrigerant cylinder

(2) Electronic balance

(3) Pressure gauge

(4) Connection nut

(5) Low pressure needle valve

NO TICE

Charge refrigerant on the basis of the precharging.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

12 Component Replacement

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

186

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Haier IKI-09 User Manual preview
IKI-09
Brand: Haier Pages: 28
Lennox MS7 Quick Manual preview
MS7
Brand: Lennox Pages: 12
Daikin FTXB25BV1 Installation Manual preview
FTXB25BV1
Brand: Daikin Pages: 38
Hisense KF-2302GWE Instruction & Installation Manual preview
KF-2302GWE
Brand: Hisense Pages: 43
Kroll LR5300-P Manual preview
LR5300-P
Brand: Kroll Pages: 28
Daikin FTYNV20AV1 Owner'S Manual preview
FTYNV20AV1
Brand: Daikin Pages: 40
eta Silentino DIGI Manual preview
Silentino DIGI
Brand: eta Pages: 64
Cercon Clean 230VAC Instructions For Use Manual preview
Clean 230VAC
Brand: Cercon Pages: 15
SNOWJOE Sunjoe SWD2500 Operator'S Manual preview
Sunjoe SWD2500
Brand: SNOWJOE Pages: 16
Bissell Auto-Mate® Corded Hand Vacuum User Manual preview
Auto-Mate® Corded Hand Vacuum
Brand: Bissell Pages: 8
York 035-08460-001 Owner'S Manual preview
035-08460-001
Brand: York Pages: 4
Prem-I-Air EH1614/EU Manual preview
EH1614/EU
Brand: Prem-I-Air Pages: 15
Vivax VC-1800 User Manual preview
VC-1800
Brand: Vivax Pages: 28
Olimpia splendid DOLCECLIMA COMPACT Instructions For Installation, Use And Maintenance Manual preview
DOLCECLIMA COMPACT
Brand: Olimpia splendid Pages: 66
WOODLAND SCENICS MODEL-VAC FS640 Instructions preview
MODEL-VAC FS640
Brand: WOODLAND SCENICS Pages: 2
Radialight AER Pro Operating Instructions Manual preview
AER Pro
Brand: Radialight Pages: 16
gmc aircon GMCAB15 User Manual preview
GMCAB15
Brand: gmc aircon Pages: 10
Olimpia splendid AQUARIA 16 Installation, Use And Maintenance Instructions preview
AQUARIA 16
Brand: Olimpia splendid Pages: 44

Brands by name

Popular brands

Load more brands