Huawei FusionCol8000-E24 User Manual Download Page 235

Page: 235 / 269

Table B-1 Repainting description

Paint Damage

Tools and

Materials

Procedure

Description

Slight scratch

(steel base

material not

exposed)

Spray paint or

paint, brush

(required for

repainting a small

area), fine

sandpaper,

anhydrous

alcohol, cotton

cloth, painting

gun (required for

repainting a large

area)

Steps 1, 2, and 4

1. For the color of

the topcoat

(polyurethane

paint), see the

delivered color

palette and

Pantone

number

specified on it.

2. For a few

smudges,

scratches, or

rust, manual

paint spraying

or brushing is

recommended.

3. For many

scratches or

large-area

smudges and

rust, use a

painting gun to

spray paint.

4. The paint

coating should

be thin and

even. Paint

drops are

prohibited on

the coating.

The surface

should be

smooth.

5. Leave the

repainted area

for about 60

minutes before

performing any

further

operation.

Smudges and rust

that cannot be

wiped off

Deep scratch

(primer damaged,

steel base

material exposed)

Spray paint or

paint, zinc-rich

primer, brush

(required for

repainting a small

area), fine

sandpaper,

anhydrous

alcohol, cotton

cloth, painting

gun (required for

repainting a large

area)

Steps 1, 2, 3, and

Logo and pattern

damage

Seek help from the headquarters for a detailed painting

solution. Frontline personnel can turn to local

advertisement coating suppliers.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

B Repainting the Unit

226

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands